Asko Dryers Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E01
Dryer will not start; display shows E01 shortly after pressing Start.
Door Lock / Door Switch Fault
E02
Dryer stops shortly after start or will not start; E02 displayed.
Overheating / High Temperature Cut-Out
E03
Dryer runs but clothes remain wet; E03 displayed near end of cycle.
Moisture Sensor / Drying Sensor Fault
E04
Dryer stops mid-cycle and displays E04; the interior may feel very hot.
Exhaust Airflow Restriction / Overheat Protection
E05
Dryer will not heat; E05 is displayed after a few minutes of running.
Heater Circuit Fault
E06
Dryer drum does not turn; the motor hums or stops; E06 is displayed.
Drive Motor / Belt Fault
E07
Dryer stops and displays E07; this may occur shortly after starting.
Motor Overload / Motor Overheating
E08
Dryer will not start; E08 is displayed; sometimes accompanied by clicking from the control area.
Main Control Board / Relay Fault
E09
Dryer display shows E09; the unit may not respond to button presses.
User Interface / Control Panel Communication Error
E10
Dryer shows E10 and stops; this is often associated with very long drying times.
Inlet Air Temperature Sensor Fault
E11
Dryer shows E11; it may stop heating or terminate the cycle prematurely.
Exhaust Temperature Sensor Fault
E12
Dryer displays E12; it may not start or may shut down quickly.
Humidity / Moisture Sensor Circuit Error
E13
Dryer shows E13; this may be associated with internal fan issues on some Asko condenser/heat pump dryers.
Internal Circulation Fan Fault
E14
Dryer displays E14; cycle may not start or may stop unexpectedly.
Water Tank / Condensate Level Error (Condenser/Heat Pump Models)
E15
Dryer shows E15; may be associated with heat pump system on certain Asko models.
Heat Pump System Fault (Heat Pump Dryers)
E16
Dryer displays E16; may not heat properly or may shut down.
Heater Relay / Power Relay Error
E17
Dryer shows E17; may not start or may stop with a beeping alarm.
Door Locking System Error
E18
Dryer displays E18; may be associated with internal temperature safety systems.
Safety Thermostat / Thermal Cut-Out Tripped
E19
Dryer shows E19; may not respond correctly to selected programs.
Program Memory / Configuration Error
E20
Dryer shows E20; may be associated with internal communication between boards on advanced models.
Internal Communication Bus Error
Symptom
Dryer powers on, but the Start button does nothing; the display may show normal time but there is no response.
User Interface Input Failure
Symptom
Dryer runs but does not heat; clothes remain cold and damp at end of cycle (no error code).
No Heat Condition
Symptom
Dryer takes too long to dry; cycles run much longer than normal and clothes are still slightly damp.
Poor Drying Performance / Extended Dry Times
Symptom
Dryer will not start at all; no drum movement when Start is pressed, though lights may be on.
No Start Condition
Symptom
The dryer display flickers or resets when starting a cycle.
Power Supply / Voltage Drop Issue
Symptom
The dryer display works, but the time remaining does not count down correctly; the cycle seems to run indefinitely.
Auto-Sense / Moisture Detection Miscalibration
Symptom
The dryer door pops open during the cycle, causing the dryer to stop.
Door Latch / Strike Wear
Symptom
The dryer door will not open at the end of the cycle; the door appears locked even though the machine is off.
Door Lock Stuck Closed
Symptom
The dryer drum does not turn, but you hear the motor running or humming.
Broken or Slipped Drive Belt
Symptom
The dryer drum light does not turn on when the door is opened, but the dryer otherwise works.
Drum Light Circuit Failure
Symptom
The dryer drum turns, but there is a loud squealing or screeching noise during operation.
Drum Support / Idler Pulley Wear
Symptom
The dryer emits a burning smell during operation, with or without visible smoke.
Overheating / Lint Ignition Risk
Symptom
The dryer has a musty or moldy odor that transfers to clothes.
Odor / Bacterial Growth
Symptom
The dryer leaks water onto the floor during or after operation (condenser/heat pump models).
Water Leak / Condensate Management Fault
Symptom
The dryer makes a loud thumping or banging noise, especially with larger loads.
Drum Roller Flat Spots / Out-of-Round Drum Support
Symptom
The dryer makes a rattling or clinking noise, especially at certain drum speeds.
Foreign Object in Drum or Blower
Symptom
The dryer runs for a few minutes, then shuts off and will not restart until it cools down.
Motor Overheating / Thermal Protector Tripping
Symptom
The dryer runs, but clothes come out wrinkled and very hot, even on low heat settings.
Temperature Regulation / Cycling Thermostat Fault
Symptom
The dryer runs, but there is a low rumbling or grinding noise that gets worse over time.
Drum Bearing / Rear Support Wear
Symptom
The dryer stops mid-cycle and the display is completely blank; power returns after some time.
Overheating Control Board / Power Supply Interruption
Symptom
The dryer vibrates excessively or 'walks' across the floor during operation.
Excessive Vibration / Imbalance
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E01 |
Dryer will not start; display shows E01 shortly after pressing Start.
|
Door Lock / Door Switch Fault | View Details |
| E02 |
Dryer stops shortly after start or will not start; E02 displayed.
|
Overheating / High Temperature Cut-Out | View Details |
| E03 |
Dryer runs but clothes remain wet; E03 displayed near end of cycle.
|
Moisture Sensor / Drying Sensor Fault | View Details |
| E04 |
Dryer stops mid-cycle and displays E04; the interior may feel very hot.
|
Exhaust Airflow Restriction / Overheat Protection | View Details |
| E05 |
Dryer will not heat; E05 is displayed after a few minutes of running.
|
Heater Circuit Fault | View Details |
| E06 |
Dryer drum does not turn; the motor hums or stops; E06 is displayed.
|
Drive Motor / Belt Fault | View Details |
| E07 |
Dryer stops and displays E07; this may occur shortly after starting.
|
Motor Overload / Motor Overheating | View Details |
| E08 |
Dryer will not start; E08 is displayed; sometimes accompanied by clicking from the control area.
|
Main Control Board / Relay Fault | View Details |
| E09 |
Dryer display shows E09; the unit may not respond to button presses.
|
User Interface / Control Panel Communication Error | View Details |
| E10 |
Dryer shows E10 and stops; this is often associated with very long drying times.
|
Inlet Air Temperature Sensor Fault | View Details |
| E11 |
Dryer shows E11; it may stop heating or terminate the cycle prematurely.
|
Exhaust Temperature Sensor Fault | View Details |
| E12 |
Dryer displays E12; it may not start or may shut down quickly.
|
Humidity / Moisture Sensor Circuit Error | View Details |
| E13 |
Dryer shows E13; this may be associated with internal fan issues on some Asko condenser/heat pump dryers.
|
Internal Circulation Fan Fault | View Details |
| E14 |
Dryer displays E14; cycle may not start or may stop unexpectedly.
|
Water Tank / Condensate Level Error (Condenser/Heat Pump Models) | View Details |
| E15 |
Dryer shows E15; may be associated with heat pump system on certain Asko models.
|
Heat Pump System Fault (Heat Pump Dryers) | View Details |
| E16 |
Dryer displays E16; may not heat properly or may shut down.
|
Heater Relay / Power Relay Error | View Details |
| E17 |
Dryer shows E17; may not start or may stop with a beeping alarm.
|
Door Locking System Error | View Details |
| E18 |
Dryer displays E18; may be associated with internal temperature safety systems.
|
Safety Thermostat / Thermal Cut-Out Tripped | View Details |
| E19 |
Dryer shows E19; may not respond correctly to selected programs.
|
Program Memory / Configuration Error | View Details |
| E20 |
Dryer shows E20; may be associated with internal communication between boards on advanced models.
|
Internal Communication Bus Error | View Details |
| – |
Dryer powers on, but the Start button does nothing; the display may show normal time but there is no response.
|
User Interface Input Failure | View Details |
| – |
Dryer runs but does not heat; clothes remain cold and damp at end of cycle (no error code).
|
No Heat Condition | View Details |
| – |
Dryer takes too long to dry; cycles run much longer than normal and clothes are still slightly damp.
|
Poor Drying Performance / Extended Dry Times | View Details |
| – |
Dryer will not start at all; no drum movement when Start is pressed, though lights may be on.
|
No Start Condition | View Details |
| – |
The dryer display flickers or resets when starting a cycle.
|
Power Supply / Voltage Drop Issue | View Details |
| – |
The dryer display works, but the time remaining does not count down correctly; the cycle seems to run indefinitely.
|
Auto-Sense / Moisture Detection Miscalibration | View Details |
| – |
The dryer door pops open during the cycle, causing the dryer to stop.
|
Door Latch / Strike Wear | View Details |
| – |
The dryer door will not open at the end of the cycle; the door appears locked even though the machine is off.
|
Door Lock Stuck Closed | View Details |
| – |
The dryer drum does not turn, but you hear the motor running or humming.
|
Broken or Slipped Drive Belt | View Details |
| – |
The dryer drum light does not turn on when the door is opened, but the dryer otherwise works.
|
Drum Light Circuit Failure | View Details |
| – |
The dryer drum turns, but there is a loud squealing or screeching noise during operation.
|
Drum Support / Idler Pulley Wear | View Details |
| – |
The dryer emits a burning smell during operation, with or without visible smoke.
|
Overheating / Lint Ignition Risk | View Details |
| – |
The dryer has a musty or moldy odor that transfers to clothes.
|
Odor / Bacterial Growth | View Details |
| – |
The dryer leaks water onto the floor during or after operation (condenser/heat pump models).
|
Water Leak / Condensate Management Fault | View Details |
| – |
The dryer makes a loud thumping or banging noise, especially with larger loads.
|
Drum Roller Flat Spots / Out-of-Round Drum Support | View Details |
| – |
The dryer makes a rattling or clinking noise, especially at certain drum speeds.
|
Foreign Object in Drum or Blower | View Details |
| – |
The dryer runs for a few minutes, then shuts off and will not restart until it cools down.
|
Motor Overheating / Thermal Protector Tripping | View Details |
| – |
The dryer runs, but clothes come out wrinkled and very hot, even on low heat settings.
|
Temperature Regulation / Cycling Thermostat Fault | View Details |
| – |
The dryer runs, but there is a low rumbling or grinding noise that gets worse over time.
|
Drum Bearing / Rear Support Wear | View Details |
| – |
The dryer stops mid-cycle and the display is completely blank; power returns after some time.
|
Overheating Control Board / Power Supply Interruption | View Details |
| – |
The dryer vibrates excessively or 'walks' across the floor during operation.
|
Excessive Vibration / Imbalance | View Details |
No matching codes found
Advertisements