Severin Multicookers Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E1
Multicooker displays E1 shortly after starting and stops heating.
Bottom temperature sensor (NTC) open circuit
E10
E10 error, cooker does not start and may show blinking icons.
Internal communication error between display panel and main control board.
E11
E11 error, cooker cannot detect the inner pot and refuses to start.
Pot detection sensor fault (weight or contact sensor).
E12
E12 error, cooker stops and displays an error during keep-warm or low-temperature cooking.
Low-temperature control instability / sensor drift.
E13
E13 error, cooker aborts the pressure program shortly after reaching pressure.
Abnormal pressure drop or leak detected.
E14
E14 error, cooker will not enter pressure mode and times out.
Pressure build-up timeout.
E15
E15 error, cooker beeps and shows an error when trying to start any program.
Ambient temperature too high or ventilation blocked.
E16
E16 error, display flickers and cooker shuts down.
Input power anomaly or low-voltage detection.
E17
E17 error, cooker cannot detect the lid closed for pressure programs.
Lid closed sensor / hall sensor fault.
E18
E18 error: The cooker stops and displays an error during sauté or high-temperature frying.
High-temperature protection activated at heating plate
E19
E19 error: The cooker beeps and refuses to start, sometimes after a liquid spill.
Moisture or short circuit detected on sensor or keypad lines
E2
E2 error appears, cooking stops, and the unit may not heat properly.
Bottom temperature sensor (NTC) short circuit or out-of-range low resistance
E20
E20 error: The cooker cannot maintain the set pressure and cycles off.
Pressure regulation instability
E3
E3 error occurs during preheat or pressure build-up, and the unit stops heating.
Overtemperature protection triggered at bottom heater
E4
E4 error appears when trying to start a pressure program.
Lid temperature sensor (upper NTC) fault
E5
E5 error occurs during pressure cooking, and the cooker beeps and stops.
Pressure sensor circuit fault or out-of-range signal
E6
E6 error appears, and the cooker will not start any program.
Main control board temperature/pressure reading conflict or internal self-test failure
E7
E7 error occurs when starting or during a pressure program, and the unit may not build pressure.
Lid lock / lid position sensor fault
E8
E8 error, cooker beeps and cancels program shortly after start.
Overpressure or steam release system fault.
E9
E9 error, unit fails to heat or stops mid-cycle.
Heating element or power drive circuit fault.
Symptom
Burnt food stuck to the bottom, frequent 'burn' smell, or food scorching before the program ends.
Localized overheating / poor temperature regulation at the pot bottom.
Symptom
Condensation or water dripping from lid onto countertop during cooking
Condensation management / overflow from condensation collector
Symptom
Excessive steam or liquid spurting from the steam release valve during pressure cooking.
Steam release valve contamination or incorrect operation
Symptom
Food undercooked or programs end too early compared to recipe times
Underheating / incorrect temperature or pressure control
Symptom
Keep-warm mode does not keep food hot; food cools down quickly
Keep-warm underheating
Symptom
Keep-warm mode overheats food, causing it to dry out or burn
Keep-warm temperature too high
Symptom
Lid is difficult to open after cooking, even when pressure indicator is down
Mechanical binding of lid lock
Symptom
Loud clicking, popping, or metallic noises during heating or pressure build-up
Thermal expansion noises / mechanical stress
Symptom
Multicooker trips household circuit breaker or RCD when plugged in or when heating starts
Electrical short or earth leakage
Symptom
Non-stick coated inner pot has peeling or flaking coating
Non-stick coating failure
Symptom
Rust spots or discoloration inside the stainless-steel inner pot
Surface corrosion / coating damage
Symptom
Strong burnt plastic or electrical smell during use
Overheating of wiring or plastic components
Symptom
Strong, persistent food odors from lid and sealing ring even after washing
Odor absorption in silicone and plastic parts
Symptom
The display lights up, but buttons do not respond or respond intermittently.
Keypad / touch panel failure
Symptom
The inner pot does not sit flat, wobbles, or makes scraping noises when inserted.
Deformed inner pot or misaligned spring plate
Symptom
The multicooker does not power on at all; there are no lights or display.
No mains power / input protection failure
Symptom
The multicooker heats but never reaches pressure, with steam constantly escaping from the lid.
Lid sealing failure under pressure
Symptom
Timer or clock runs too fast or too slow, affecting cooking duration
Timing circuit / oscillator drift
Symptom
Unusual humming or buzzing sound from inside the cooker during operation
Electrical vibration or fan noise
Symptom
Water or food leaking from around the lid hinge or the sides of the lid.
Lid body or hinge seal leakage
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E1 |
Multicooker displays E1 shortly after starting and stops heating.
|
Bottom temperature sensor (NTC) open circuit | View Details |
| E10 |
E10 error, cooker does not start and may show blinking icons.
|
Internal communication error between display panel and main control board. | View Details |
| E11 |
E11 error, cooker cannot detect the inner pot and refuses to start.
|
Pot detection sensor fault (weight or contact sensor). | View Details |
| E12 |
E12 error, cooker stops and displays an error during keep-warm or low-temperature cooking.
|
Low-temperature control instability / sensor drift. | View Details |
| E13 |
E13 error, cooker aborts the pressure program shortly after reaching pressure.
|
Abnormal pressure drop or leak detected. | View Details |
| E14 |
E14 error, cooker will not enter pressure mode and times out.
|
Pressure build-up timeout. | View Details |
| E15 |
E15 error, cooker beeps and shows an error when trying to start any program.
|
Ambient temperature too high or ventilation blocked. | View Details |
| E16 |
E16 error, display flickers and cooker shuts down.
|
Input power anomaly or low-voltage detection. | View Details |
| E17 |
E17 error, cooker cannot detect the lid closed for pressure programs.
|
Lid closed sensor / hall sensor fault. | View Details |
| E18 |
E18 error: The cooker stops and displays an error during sauté or high-temperature frying.
|
High-temperature protection activated at heating plate | View Details |
| E19 |
E19 error: The cooker beeps and refuses to start, sometimes after a liquid spill.
|
Moisture or short circuit detected on sensor or keypad lines | View Details |
| E2 |
E2 error appears, cooking stops, and the unit may not heat properly.
|
Bottom temperature sensor (NTC) short circuit or out-of-range low resistance | View Details |
| E20 |
E20 error: The cooker cannot maintain the set pressure and cycles off.
|
Pressure regulation instability | View Details |
| E3 |
E3 error occurs during preheat or pressure build-up, and the unit stops heating.
|
Overtemperature protection triggered at bottom heater | View Details |
| E4 |
E4 error appears when trying to start a pressure program.
|
Lid temperature sensor (upper NTC) fault | View Details |
| E5 |
E5 error occurs during pressure cooking, and the cooker beeps and stops.
|
Pressure sensor circuit fault or out-of-range signal | View Details |
| E6 |
E6 error appears, and the cooker will not start any program.
|
Main control board temperature/pressure reading conflict or internal self-test failure | View Details |
| E7 |
E7 error occurs when starting or during a pressure program, and the unit may not build pressure.
|
Lid lock / lid position sensor fault | View Details |
| E8 |
E8 error, cooker beeps and cancels program shortly after start.
|
Overpressure or steam release system fault. | View Details |
| E9 |
E9 error, unit fails to heat or stops mid-cycle.
|
Heating element or power drive circuit fault. | View Details |
| – |
Burnt food stuck to the bottom, frequent 'burn' smell, or food scorching before the program ends.
|
Localized overheating / poor temperature regulation at the pot bottom. | View Details |
| – |
Condensation or water dripping from lid onto countertop during cooking
|
Condensation management / overflow from condensation collector | View Details |
| – |
Excessive steam or liquid spurting from the steam release valve during pressure cooking.
|
Steam release valve contamination or incorrect operation | View Details |
| – |
Food undercooked or programs end too early compared to recipe times
|
Underheating / incorrect temperature or pressure control | View Details |
| – |
Keep-warm mode does not keep food hot; food cools down quickly
|
Keep-warm underheating | View Details |
| – |
Keep-warm mode overheats food, causing it to dry out or burn
|
Keep-warm temperature too high | View Details |
| – |
Lid is difficult to open after cooking, even when pressure indicator is down
|
Mechanical binding of lid lock | View Details |
| – |
Loud clicking, popping, or metallic noises during heating or pressure build-up
|
Thermal expansion noises / mechanical stress | View Details |
| – |
Multicooker trips household circuit breaker or RCD when plugged in or when heating starts
|
Electrical short or earth leakage | View Details |
| – |
Non-stick coated inner pot has peeling or flaking coating
|
Non-stick coating failure | View Details |
| – |
Rust spots or discoloration inside the stainless-steel inner pot
|
Surface corrosion / coating damage | View Details |
| – |
Strong burnt plastic or electrical smell during use
|
Overheating of wiring or plastic components | View Details |
| – |
Strong, persistent food odors from lid and sealing ring even after washing
|
Odor absorption in silicone and plastic parts | View Details |
| – |
The display lights up, but buttons do not respond or respond intermittently.
|
Keypad / touch panel failure | View Details |
| – |
The inner pot does not sit flat, wobbles, or makes scraping noises when inserted.
|
Deformed inner pot or misaligned spring plate | View Details |
| – |
The multicooker does not power on at all; there are no lights or display.
|
No mains power / input protection failure | View Details |
| – |
The multicooker heats but never reaches pressure, with steam constantly escaping from the lid.
|
Lid sealing failure under pressure | View Details |
| – |
Timer or clock runs too fast or too slow, affecting cooking duration
|
Timing circuit / oscillator drift | View Details |
| – |
Unusual humming or buzzing sound from inside the cooker during operation
|
Electrical vibration or fan noise | View Details |
| – |
Water or food leaking from around the lid hinge or the sides of the lid.
|
Lid body or hinge seal leakage | View Details |
No matching codes found
Advertisements