Asko Washing Machines Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E01
Washer will not start; display shows E01 shortly after pressing Start
Door Lock Failure
E02
Washer does not fill with water; E02 displayed after a short time
Water Inlet Timeout / Fill Fault
E03
Washer does not drain; E03 appears and cycle stops with water in drum
Drain Pump Timeout / Drain Failure
E04
Washer overfills or shows E04 and stops with water level too high
Overfill / Water Level Sensor Fault
E05
Washer stops heating water; E05 displayed during wash cycle
Heating Circuit Failure
E06
Washer drum does not spin or tumble; E06 displayed
Motor Drive Fault
E07
Washer stops mid-cycle and displays E07; this may relate to the door or safety interlock.
Door Interlock / Safety Circuit Error
E08
Washer displays E08 and may not start or may stop during a cycle; this is often related to water level sensing.
Pressure Sensor / Water Level Error
E09
Washer displays E09 and will not run; this is often associated with control electronics.
Main Control Board Failure
E10
Washer displays E10 and does not heat or complete the cycle properly.
NTC Temperature Sensor Fault
E11
Washer displays E11; this may be related to the hot water inlet or a temperature mismatch.
Hot Water Inlet / Temperature Inconsistency
E12
Washer displays E12 and may stop during spin or drain phases.
Unbalanced Load / Spin Protection Fault
E13
Washer displays E13; this is often associated with water leakage or overflow protection.
Leakage / Anti-Flood System Activation
E14
Washer displays E14; this may be related to communication between control boards (on models with separate motor control).
Communication Error Between Main PCB and Motor/Inverter Board
E15
Washer displays E15; it may not start or may stop unexpectedly.
User Interface / Display Board Fault
E16
Washer displays E16; this may be associated with door unlocking at the end of a cycle.
Door Unlock Failure
E17
Washer displays E17, often related to excessive foam or suds detection.
Excessive Suds / Foam Detection
E18
Washer displays E18, which may be associated with a low water level or dry running.
Insufficient Water Supply / Dry Protection
E19
Washer displays E19, which may be related to the drain or recirculation system on some Asko models.
Recirculation / Auxiliary Pump Fault
E20
Washer displays E20, which may be associated with motor overheating or overload.
Motor Overload / Overheat Protection
Symptom
Washer does not dispense detergent or softener from the drawer properly.
Detergent Dispenser Malfunction
Symptom
Washer does not fill with hot water; only cold water is used, even on hot cycles.
Hot Water Supply / Valve Issue
Symptom
Washer door will not unlock at the end of the cycle; no error code is shown.
Door Stuck Locked
Symptom
Washer drum does not stop immediately after pressing Pause or opening door (where door can open mid-cycle)
Brake / Motor Control Delay
Symptom
Washer drum has excessive play when pushed up and down; a scraping noise may be heard.
Suspension or Spider Arm Wear
Symptom
Washer emits a burning smell or smoke during operation.
Overheating Component / Electrical Burn
Symptom
Washer fills and drains, but the drum does not turn at all during wash or spin.
Complete Drum Drive Failure
Symptom
Washer fills with water even when turned off, slowly over time.
Inlet Valve Not Closing Properly
Symptom
Washer has a strong musty or moldy odor inside the drum.
Biofilm / Mold Build-Up in Tub and Hoses
Symptom
Washer intermittently trips the household circuit breaker or RCD during operation.
Electrical Short or Ground Fault
Symptom
Washer leaks water from the front door area during a wash cycle.
Door Gasket (Boot) Leak
Symptom
Washer leaks water from underneath or the rear of the machine.
Internal Hose or Component Leak
Symptom
Washer leaves clothes soaking wet at the end of the cycle; spin seems weak or does not reach full speed.
Poor Spin Performance
Symptom
Washer makes loud banging or knocking during spin; the machine may move across the floor.
Excessive Vibration / Out-of-Balance Spin
Symptom
Washer powers on but will not start any cycle; the Start button is unresponsive.
User Interface Input Failure
Symptom
Washer spins but makes a very loud rumbling or roaring noise, especially at high speed.
Tub Bearing Failure
Symptom
Washer takes much longer than expected to complete cycles.
Extended Cycle Time / Program Overrun
Symptom
Washer will not power on at all; no lights or display.
No Power / Dead Machine
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E01 |
Washer will not start; display shows E01 shortly after pressing Start
|
Door Lock Failure | View Details |
| E02 |
Washer does not fill with water; E02 displayed after a short time
|
Water Inlet Timeout / Fill Fault | View Details |
| E03 |
Washer does not drain; E03 appears and cycle stops with water in drum
|
Drain Pump Timeout / Drain Failure | View Details |
| E04 |
Washer overfills or shows E04 and stops with water level too high
|
Overfill / Water Level Sensor Fault | View Details |
| E05 |
Washer stops heating water; E05 displayed during wash cycle
|
Heating Circuit Failure | View Details |
| E06 |
Washer drum does not spin or tumble; E06 displayed
|
Motor Drive Fault | View Details |
| E07 |
Washer stops mid-cycle and displays E07; this may relate to the door or safety interlock.
|
Door Interlock / Safety Circuit Error | View Details |
| E08 |
Washer displays E08 and may not start or may stop during a cycle; this is often related to water level sensing.
|
Pressure Sensor / Water Level Error | View Details |
| E09 |
Washer displays E09 and will not run; this is often associated with control electronics.
|
Main Control Board Failure | View Details |
| E10 |
Washer displays E10 and does not heat or complete the cycle properly.
|
NTC Temperature Sensor Fault | View Details |
| E11 |
Washer displays E11; this may be related to the hot water inlet or a temperature mismatch.
|
Hot Water Inlet / Temperature Inconsistency | View Details |
| E12 |
Washer displays E12 and may stop during spin or drain phases.
|
Unbalanced Load / Spin Protection Fault | View Details |
| E13 |
Washer displays E13; this is often associated with water leakage or overflow protection.
|
Leakage / Anti-Flood System Activation | View Details |
| E14 |
Washer displays E14; this may be related to communication between control boards (on models with separate motor control).
|
Communication Error Between Main PCB and Motor/Inverter Board | View Details |
| E15 |
Washer displays E15; it may not start or may stop unexpectedly.
|
User Interface / Display Board Fault | View Details |
| E16 |
Washer displays E16; this may be associated with door unlocking at the end of a cycle.
|
Door Unlock Failure | View Details |
| E17 |
Washer displays E17, often related to excessive foam or suds detection.
|
Excessive Suds / Foam Detection | View Details |
| E18 |
Washer displays E18, which may be associated with a low water level or dry running.
|
Insufficient Water Supply / Dry Protection | View Details |
| E19 |
Washer displays E19, which may be related to the drain or recirculation system on some Asko models.
|
Recirculation / Auxiliary Pump Fault | View Details |
| E20 |
Washer displays E20, which may be associated with motor overheating or overload.
|
Motor Overload / Overheat Protection | View Details |
| – |
Washer does not dispense detergent or softener from the drawer properly.
|
Detergent Dispenser Malfunction | View Details |
| – |
Washer does not fill with hot water; only cold water is used, even on hot cycles.
|
Hot Water Supply / Valve Issue | View Details |
| – |
Washer door will not unlock at the end of the cycle; no error code is shown.
|
Door Stuck Locked | View Details |
| – |
Washer drum does not stop immediately after pressing Pause or opening door (where door can open mid-cycle)
|
Brake / Motor Control Delay | View Details |
| – |
Washer drum has excessive play when pushed up and down; a scraping noise may be heard.
|
Suspension or Spider Arm Wear | View Details |
| – |
Washer emits a burning smell or smoke during operation.
|
Overheating Component / Electrical Burn | View Details |
| – |
Washer fills and drains, but the drum does not turn at all during wash or spin.
|
Complete Drum Drive Failure | View Details |
| – |
Washer fills with water even when turned off, slowly over time.
|
Inlet Valve Not Closing Properly | View Details |
| – |
Washer has a strong musty or moldy odor inside the drum.
|
Biofilm / Mold Build-Up in Tub and Hoses | View Details |
| – |
Washer intermittently trips the household circuit breaker or RCD during operation.
|
Electrical Short or Ground Fault | View Details |
| – |
Washer leaks water from the front door area during a wash cycle.
|
Door Gasket (Boot) Leak | View Details |
| – |
Washer leaks water from underneath or the rear of the machine.
|
Internal Hose or Component Leak | View Details |
| – |
Washer leaves clothes soaking wet at the end of the cycle; spin seems weak or does not reach full speed.
|
Poor Spin Performance | View Details |
| – |
Washer makes loud banging or knocking during spin; the machine may move across the floor.
|
Excessive Vibration / Out-of-Balance Spin | View Details |
| – |
Washer powers on but will not start any cycle; the Start button is unresponsive.
|
User Interface Input Failure | View Details |
| – |
Washer spins but makes a very loud rumbling or roaring noise, especially at high speed.
|
Tub Bearing Failure | View Details |
| – |
Washer takes much longer than expected to complete cycles.
|
Extended Cycle Time / Program Overrun | View Details |
| – |
Washer will not power on at all; no lights or display.
|
No Power / Dead Machine | View Details |
No matching codes found
Advertisements