Gram Washing Machines Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E01
The washer will not start; the display shows E01 immediately after pressing Start.
Door Lock Failure
E02
The washer does not fill with water or fills very slowly; E02 is displayed after a few minutes.
Water Inlet Timeout / Fill Fault
E03
Washer will not drain; water remains in the drum, and E03 appears.
Drain Pump Timeout / Drain Fault
E04
Washer overfills or shows E04 with water close to the door seal.
Overfill / Water Level Sensor Fault
E05
Washer does not heat water; the cycle takes unusually long, and E05 is displayed.
Heating Circuit Fault
E06
Washer stops mid-cycle and displays E06; the drum does not rotate.
Motor Tachometer / Speed Sensor Fault
E07
Washer attempts to spin but stops and shows E07; drum movement is jerky or weak.
Motor Drive Fault / Overload
E08
Washer does not spin; E08 is displayed near the end of the cycle.
Unbalanced Load / Spin Protection
E09
Washer stops and displays E09; no drum movement, sometimes tripping the household breaker.
Motor Short Circuit / Power Module Fault
E10
Washer shows E10 and does not start; the door may not lock properly.
Door Not Closed / Door Sensor Error
E11
Washer stops with E11; water remains in the drum, and the door stays locked longer than usual.
Drain / Water Level Not Reached for Spin
E12
Washer displays E12; water temperature is incorrect (too cold or too hot) for the selected program.
Temperature Sensor (NTC) Fault
E13
Washer displays E13 and may stop mid-cycle, sometimes accompanied by water under the machine.
Leak Detected / Overflow Protection
E14
Washer displays E14; the control panel may be unresponsive or behave erratically.
Control Panel / Communication Fault
E15
Washer displays E15; the cycle may not start or may stop unexpectedly.
Power Supply / Voltage Fault
E16
Washer displays E16; the door may unlock unexpectedly or not lock at all during cycle selection.
Door Lock Circuit Error
E17
Washer displays E17 shortly after starting; no water enters the drum.
No Water Supply Detected
E18
Washer stops with E18; the drum contains water and the machine will not proceed to spin.
Drain Time Exceeded
E19
Washer displays E19; the program may freeze or skip the heating phase.
Heater Relay / Triac Error
E20
Washer displays E20; the drum does not rotate at all during wash or spin.
Motor Control Communication Error
Symptom
Washer displays random lights or resets mid-cycle without an error code
Intermittent Power or Control Fault
Symptom
Washer does not take fabric softener from the dispenser drawer
Dispenser Siphon or Jet Blockage
Symptom
Washer door will not unlock at the end of the cycle
Door Lock Stuck or Safety Interlock Delay
Symptom
Washer drum does not turn at all, but the machine fills and drains normally
Drive System Failure
Symptom
Washer emits a burning smell during operation
Overheating Component or Friction
Symptom
Washer fills and drains, but clothes come out dirty or with detergent residue
Poor Wash Performance
Symptom
Washer has a persistent bad odor inside the drum
Biofilm and Detergent Residue Build-up
Symptom
Washer intermittently trips the household RCD (residual current device) or GFCI
Earth Leakage / Insulation Fault
Symptom
Washer is leaking water from the front during or after a wash cycle.
Door Seal (Gasket) Leak
Symptom
Washer is leaking water from underneath the cabinet.
Internal Hose or Pump Leak
Symptom
Washer leaves black or greasy marks on clothes
Contamination from Seal, Bearings, or Detergent Build-up
Symptom
Washer leaves clothes very wet at the end of the cycle
Insufficient Spin Extraction
Symptom
Washer makes loud banging or knocking noises during spin
Suspension or Drum Support Failure
Symptom
Washer produces a high-pitched squealing or grinding noise during the spin cycle
Drum Bearing or Drive Pulley Wear
Symptom
Washer takes much longer than the displayed time to complete a cycle
Cycle Time Extension Due to Load or Heating Issues
Symptom
Washer vibrates excessively or 'walks' across the floor during spin
Excessive Vibration or Unbalanced Operation
Symptom
Washer will not start; all lights are off and the display is blank
No Power or Dead Appliance
Symptom
Washer will not start; display is on but the Start button does nothing
User Interface or Door Lock Start Inhibit
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E01 |
The washer will not start; the display shows E01 immediately after pressing Start.
|
Door Lock Failure | View Details |
| E02 |
The washer does not fill with water or fills very slowly; E02 is displayed after a few minutes.
|
Water Inlet Timeout / Fill Fault | View Details |
| E03 |
Washer will not drain; water remains in the drum, and E03 appears.
|
Drain Pump Timeout / Drain Fault | View Details |
| E04 |
Washer overfills or shows E04 with water close to the door seal.
|
Overfill / Water Level Sensor Fault | View Details |
| E05 |
Washer does not heat water; the cycle takes unusually long, and E05 is displayed.
|
Heating Circuit Fault | View Details |
| E06 |
Washer stops mid-cycle and displays E06; the drum does not rotate.
|
Motor Tachometer / Speed Sensor Fault | View Details |
| E07 |
Washer attempts to spin but stops and shows E07; drum movement is jerky or weak.
|
Motor Drive Fault / Overload | View Details |
| E08 |
Washer does not spin; E08 is displayed near the end of the cycle.
|
Unbalanced Load / Spin Protection | View Details |
| E09 |
Washer stops and displays E09; no drum movement, sometimes tripping the household breaker.
|
Motor Short Circuit / Power Module Fault | View Details |
| E10 |
Washer shows E10 and does not start; the door may not lock properly.
|
Door Not Closed / Door Sensor Error | View Details |
| E11 |
Washer stops with E11; water remains in the drum, and the door stays locked longer than usual.
|
Drain / Water Level Not Reached for Spin | View Details |
| E12 |
Washer displays E12; water temperature is incorrect (too cold or too hot) for the selected program.
|
Temperature Sensor (NTC) Fault | View Details |
| E13 |
Washer displays E13 and may stop mid-cycle, sometimes accompanied by water under the machine.
|
Leak Detected / Overflow Protection | View Details |
| E14 |
Washer displays E14; the control panel may be unresponsive or behave erratically.
|
Control Panel / Communication Fault | View Details |
| E15 |
Washer displays E15; the cycle may not start or may stop unexpectedly.
|
Power Supply / Voltage Fault | View Details |
| E16 |
Washer displays E16; the door may unlock unexpectedly or not lock at all during cycle selection.
|
Door Lock Circuit Error | View Details |
| E17 |
Washer displays E17 shortly after starting; no water enters the drum.
|
No Water Supply Detected | View Details |
| E18 |
Washer stops with E18; the drum contains water and the machine will not proceed to spin.
|
Drain Time Exceeded | View Details |
| E19 |
Washer displays E19; the program may freeze or skip the heating phase.
|
Heater Relay / Triac Error | View Details |
| E20 |
Washer displays E20; the drum does not rotate at all during wash or spin.
|
Motor Control Communication Error | View Details |
| – |
Washer displays random lights or resets mid-cycle without an error code
|
Intermittent Power or Control Fault | View Details |
| – |
Washer does not take fabric softener from the dispenser drawer
|
Dispenser Siphon or Jet Blockage | View Details |
| – |
Washer door will not unlock at the end of the cycle
|
Door Lock Stuck or Safety Interlock Delay | View Details |
| – |
Washer drum does not turn at all, but the machine fills and drains normally
|
Drive System Failure | View Details |
| – |
Washer emits a burning smell during operation
|
Overheating Component or Friction | View Details |
| – |
Washer fills and drains, but clothes come out dirty or with detergent residue
|
Poor Wash Performance | View Details |
| – |
Washer has a persistent bad odor inside the drum
|
Biofilm and Detergent Residue Build-up | View Details |
| – |
Washer intermittently trips the household RCD (residual current device) or GFCI
|
Earth Leakage / Insulation Fault | View Details |
| – |
Washer is leaking water from the front during or after a wash cycle.
|
Door Seal (Gasket) Leak | View Details |
| – |
Washer is leaking water from underneath the cabinet.
|
Internal Hose or Pump Leak | View Details |
| – |
Washer leaves black or greasy marks on clothes
|
Contamination from Seal, Bearings, or Detergent Build-up | View Details |
| – |
Washer leaves clothes very wet at the end of the cycle
|
Insufficient Spin Extraction | View Details |
| – |
Washer makes loud banging or knocking noises during spin
|
Suspension or Drum Support Failure | View Details |
| – |
Washer produces a high-pitched squealing or grinding noise during the spin cycle
|
Drum Bearing or Drive Pulley Wear | View Details |
| – |
Washer takes much longer than the displayed time to complete a cycle
|
Cycle Time Extension Due to Load or Heating Issues | View Details |
| – |
Washer vibrates excessively or 'walks' across the floor during spin
|
Excessive Vibration or Unbalanced Operation | View Details |
| – |
Washer will not start; all lights are off and the display is blank
|
No Power or Dead Appliance | View Details |
| – |
Washer will not start; display is on but the Start button does nothing
|
User Interface or Door Lock Start Inhibit | View Details |
No matching codes found
Advertisements