Roper Washing Machines Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
F0E1
Washer displays F0E1 and will not start or stops shortly after starting a cycle, often when heavily loaded.
Load detection error (off-balance or overloaded).
F0E2
Washer displays F0E2 and may stop mid-cycle with excessive suds visible in the tub, on the door glass (front-load), or in the basket (top-load).
Oversuds condition detected.
F0E3
Washer displays F0E3 and may stop or refuse to spin when a heavy load is present.
Overload detected by motor or control.
F0E5
Washer displays F0E5 and may stop before or during spin, often accompanied by banging or thumping.
Off-balance load detected.
F1E1
Washer displays F1E1 and will not start or complete a cycle; it may beep repeatedly.
Main control board internal error.
F1E2
Washer displays F1E2 and may not respond to button presses or may behave erratically.
User Interface (UI) or console communication error.
F1E3
Washer displays F1E3 and may not fill or start properly.
Water level pressure system error.
F2E1
Washer displays F2E1 and buttons may not respond or may seem stuck.
Stuck or shorted key on the user interface.
F2E3
The washer displays F2E3 and may not start or may stop mid-cycle.
UI to Main Control Mismatch or Communication Error
F3E1
The washer displays F3E1 and may overfill, underfill, or stop with water in the tub.
Water Level Sensor (Pressure Sensor) Fault
F3E2
The washer displays F3E2 and may not heat water properly (on models with internal heater) or may stop mid-cycle.
Water Temperature Sensor (Thermistor) Fault
F3E3
The washer displays F3E3 and may not fill correctly with hot or cold water.
Water Inlet Temperature Sensor or Thermistor Range Error
F5E1
The washer displays F5E1 and will not start; lid will not lock when cycle is started.
Lid Lock Will Not Lock
F5E2
The washer displays F5E2 and the lid remains locked at the end of the cycle or will not unlock when cancel is pressed.
Lid Lock Will Not Unlock
F5E3
The washer displays F5E3 and may not start or may stop mid-cycle with lid lock issues.
Lid Lock or Lid Switch Fault (General)
F5E4
The washer displays F5E4 and may not start; control thinks lid is open when it is closed.
Lid Not Opened Between Cycles / Lid Status Error
F5E7
The washer displays F5E7 and may not start spin or agitate.
Lid Not Closed or Locked During Spin/Agitate
F7E1
The washer displays F7E1 and will not spin or agitate; may hum briefly then stop.
Basket Speed Sensor or Motor Speed Error
F7E2
Washer displays F7E2 and may not spin or may stop during spin with a grinding noise.
Motor or Drive System Stall
F7E5
Washer displays F7E5 and may not shift between wash and spin; may stay in one mode.
Shifter/Actuator Fault
F7E6
Washer displays F7E6 and may not agitate or spin correctly.
Motor Circuit or Motor Fault
F7E7
Washer displays F7E7 and may not reach full spin speed.
Motor Unable to Reach Target RPM
F7E8
Washer displays F7E8 and may stop during spin or agitate with a hot motor.
Motor Overheating
F8E1
Washer displays F8E1 or LO FL and fills very slowly or not at all; may time out before wash begins.
Long Fill / Low Water Flow
F8E3
Washer displays F8E3 and may overflow or have water near the top of the basket or door.
Overflow Condition
F8E4
Washer displays F8E4 and may stop with water detected in the base or overflow tray (if equipped).
Flood Protection / Overflow Tray Switch Activated
F9E1
Washer displays F9E1 or LD (Long Drain) and will not complete the cycle; water remains in tub.
Long Drain Time / Drain Failure
F9E2
Washer displays F9E2 and may have intermittent drain issues or control lockups.
Drain Pump Electrical Problem
Symptom
The washer does not drain; water remains in the tub at the end of the cycle, and no error code is displayed.
Drain System Blockage or Pump Failure
Symptom
The washer emits a burning rubber or electrical smell during operation.
Overheating Component or Slipping Drive
Symptom
The washer fills with water but does not agitate; the timer or display counts down normally.
Agitation Failure
Symptom
The washer leaks water onto the floor during or after a cycle.
External Water Leak
Symptom
The washer leaves clothes very wet at the end of the cycle, but it appears to spin.
Poor Extraction / Low Spin Speed
Symptom
The washer makes a high-pitched squeal or grinding noise during spin.
Bearing or Drive System Noise
Symptom
The washer makes loud banging or thumping noises during spin.
Excessive Vibration / Off-Balance Spin
Symptom
The washer will not power on at all; there are no lights or display, but the outlet has power.
No Power to Control / Dead Washer
Symptom
The washer will not spin; clothes come out soaking wet, although it may still drain water.
Spin Failure
Symptom
The washer will not start the cycle; the lights are on, but pressing Start does nothing.
Start Circuit or Lid Switch Interlock Failure
Symptom
Washer door (front-load) will not open at end of cycle; no error code shown.
Door Lock Stuck Closed
Symptom
Washer has a musty or moldy odor inside the tub or around the door.
Biofilm and Mold Buildup
Symptom
Washer intermittently stops mid-cycle and then resumes or resets.
Intermittent Power or Control Disruption
Symptom
Washer leaves white residue or detergent streaks on clothes.
Detergent or Fabric Softener Residue
Symptom
Washer lid slams shut or does not stay up on its own.
Lid Hinge or Damper Failure
Symptom
Washer shakes or walks across the floor during spin, even with moderate loads.
Excessive Vibration Due to Installation or Suspension Issues
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| F0E1 |
Washer displays F0E1 and will not start or stops shortly after starting a cycle, often when heavily loaded.
|
Load detection error (off-balance or overloaded). | View Details |
| F0E2 |
Washer displays F0E2 and may stop mid-cycle with excessive suds visible in the tub, on the door glass (front-load), or in the basket (top-load).
|
Oversuds condition detected. | View Details |
| F0E3 |
Washer displays F0E3 and may stop or refuse to spin when a heavy load is present.
|
Overload detected by motor or control. | View Details |
| F0E5 |
Washer displays F0E5 and may stop before or during spin, often accompanied by banging or thumping.
|
Off-balance load detected. | View Details |
| F1E1 |
Washer displays F1E1 and will not start or complete a cycle; it may beep repeatedly.
|
Main control board internal error. | View Details |
| F1E2 |
Washer displays F1E2 and may not respond to button presses or may behave erratically.
|
User Interface (UI) or console communication error. | View Details |
| F1E3 |
Washer displays F1E3 and may not fill or start properly.
|
Water level pressure system error. | View Details |
| F2E1 |
Washer displays F2E1 and buttons may not respond or may seem stuck.
|
Stuck or shorted key on the user interface. | View Details |
| F2E3 |
The washer displays F2E3 and may not start or may stop mid-cycle.
|
UI to Main Control Mismatch or Communication Error | View Details |
| F3E1 |
The washer displays F3E1 and may overfill, underfill, or stop with water in the tub.
|
Water Level Sensor (Pressure Sensor) Fault | View Details |
| F3E2 |
The washer displays F3E2 and may not heat water properly (on models with internal heater) or may stop mid-cycle.
|
Water Temperature Sensor (Thermistor) Fault | View Details |
| F3E3 |
The washer displays F3E3 and may not fill correctly with hot or cold water.
|
Water Inlet Temperature Sensor or Thermistor Range Error | View Details |
| F5E1 |
The washer displays F5E1 and will not start; lid will not lock when cycle is started.
|
Lid Lock Will Not Lock | View Details |
| F5E2 |
The washer displays F5E2 and the lid remains locked at the end of the cycle or will not unlock when cancel is pressed.
|
Lid Lock Will Not Unlock | View Details |
| F5E3 |
The washer displays F5E3 and may not start or may stop mid-cycle with lid lock issues.
|
Lid Lock or Lid Switch Fault (General) | View Details |
| F5E4 |
The washer displays F5E4 and may not start; control thinks lid is open when it is closed.
|
Lid Not Opened Between Cycles / Lid Status Error | View Details |
| F5E7 |
The washer displays F5E7 and may not start spin or agitate.
|
Lid Not Closed or Locked During Spin/Agitate | View Details |
| F7E1 |
The washer displays F7E1 and will not spin or agitate; may hum briefly then stop.
|
Basket Speed Sensor or Motor Speed Error | View Details |
| F7E2 |
Washer displays F7E2 and may not spin or may stop during spin with a grinding noise.
|
Motor or Drive System Stall | View Details |
| F7E5 |
Washer displays F7E5 and may not shift between wash and spin; may stay in one mode.
|
Shifter/Actuator Fault | View Details |
| F7E6 |
Washer displays F7E6 and may not agitate or spin correctly.
|
Motor Circuit or Motor Fault | View Details |
| F7E7 |
Washer displays F7E7 and may not reach full spin speed.
|
Motor Unable to Reach Target RPM | View Details |
| F7E8 |
Washer displays F7E8 and may stop during spin or agitate with a hot motor.
|
Motor Overheating | View Details |
| F8E1 |
Washer displays F8E1 or LO FL and fills very slowly or not at all; may time out before wash begins.
|
Long Fill / Low Water Flow | View Details |
| F8E3 |
Washer displays F8E3 and may overflow or have water near the top of the basket or door.
|
Overflow Condition | View Details |
| F8E4 |
Washer displays F8E4 and may stop with water detected in the base or overflow tray (if equipped).
|
Flood Protection / Overflow Tray Switch Activated | View Details |
| F9E1 |
Washer displays F9E1 or LD (Long Drain) and will not complete the cycle; water remains in tub.
|
Long Drain Time / Drain Failure | View Details |
| F9E2 |
Washer displays F9E2 and may have intermittent drain issues or control lockups.
|
Drain Pump Electrical Problem | View Details |
| – |
The washer does not drain; water remains in the tub at the end of the cycle, and no error code is displayed.
|
Drain System Blockage or Pump Failure | View Details |
| – |
The washer emits a burning rubber or electrical smell during operation.
|
Overheating Component or Slipping Drive | View Details |
| – |
The washer fills with water but does not agitate; the timer or display counts down normally.
|
Agitation Failure | View Details |
| – |
The washer leaks water onto the floor during or after a cycle.
|
External Water Leak | View Details |
| – |
The washer leaves clothes very wet at the end of the cycle, but it appears to spin.
|
Poor Extraction / Low Spin Speed | View Details |
| – |
The washer makes a high-pitched squeal or grinding noise during spin.
|
Bearing or Drive System Noise | View Details |
| – |
The washer makes loud banging or thumping noises during spin.
|
Excessive Vibration / Off-Balance Spin | View Details |
| – |
The washer will not power on at all; there are no lights or display, but the outlet has power.
|
No Power to Control / Dead Washer | View Details |
| – |
The washer will not spin; clothes come out soaking wet, although it may still drain water.
|
Spin Failure | View Details |
| – |
The washer will not start the cycle; the lights are on, but pressing Start does nothing.
|
Start Circuit or Lid Switch Interlock Failure | View Details |
| – |
Washer door (front-load) will not open at end of cycle; no error code shown.
|
Door Lock Stuck Closed | View Details |
| – |
Washer has a musty or moldy odor inside the tub or around the door.
|
Biofilm and Mold Buildup | View Details |
| – |
Washer intermittently stops mid-cycle and then resumes or resets.
|
Intermittent Power or Control Disruption | View Details |
| – |
Washer leaves white residue or detergent streaks on clothes.
|
Detergent or Fabric Softener Residue | View Details |
| – |
Washer lid slams shut or does not stay up on its own.
|
Lid Hinge or Damper Failure | View Details |
| – |
Washer shakes or walks across the floor during spin, even with moderate loads.
|
Excessive Vibration Due to Installation or Suspension Issues | View Details |
No matching codes found
Advertisements