Beko Washer-Dryer Combos Error Codes

E01

Washer-dryer will not start; the door symbol flashes, and the cycle will not begin.

Door Lock Failure

E02

Washer-dryer does not fill with water or fills very slowly; cycle stops early

Water Inlet Timeout / Fill Fault

E03

Washer-dryer does not drain; water remains in the drum, and the program stops or will not spin.

Drain Pump Fault / Drain Timeout

E04

Washer-dryer overfills or shows overflow error; water may be visible in door glass when idle

Overfill / Pressure System Fault

E05

Washer-dryer does not heat water during the wash; clothes come out cold, and detergent is not dissolving properly.

Wash Heater Circuit Fault

E06

Washer-dryer stops mid-cycle or will not start drying; drying function not available

Dryer Heater / Drying System Fault

E07

Washer-dryer drum does not rotate during wash or spin; humming noise may be heard

Motor Drive Fault

E08

Washer-dryer fails to reach or maintain correct spin speed; may stop with wet clothes

Tachometer / Speed Feedback Fault

E09

Washer-dryer stops with water in the drum and will not proceed to spin; the pump may run continuously.

Drain / Siphon or Pressure Sensor Error

E10

The washer-dryer does not detect the water level correctly; it may stop early or run indefinitely.

Water Level Sensor / NTC Communication Fault

E11

The washer-dryer door will not unlock at the end of the cycle; E11 is displayed.

Door Unlock Timeout / Interlock Stuck

E12

The washer-dryer shows a drying error shortly after starting the drying cycle; the drum may tumble but there is no heat.

Drying Temperature Sensor / NTC Fault

E13

The washer-dryer reports a drying system fault; drying stops early and clothes remain wet.

Dryer Fan / Airflow Fault

E16

The washer-dryer displays a water inlet error; no water enters despite the tap being open.

Inlet Valve Electrical Fault

E17

The washer-dryer shows a door lock error shortly after starting; the drum does not move.

Door Lock Circuit Fault

E18

The washer-dryer shows an unbalanced load error; the spin cycle does not start or stops repeatedly.

Unbalanced Load Detection / Spin Abort

E20

The washer-dryer displays a generic motor error; the drum may not move or moves erratically.

Motor Control / Inverter Fault

E23

The washer-dryer shows a drain pump triac or electrical fault; the pump may run continuously or not at all.

Drain Pump Control Circuit Fault

E30

Washer-dryer displays a water leak or safety error; the machine may stop and attempt to drain continuously.

Anti-Flood / Leak Detection Activation

E40

Washer-dryer shows a 'door open' error even when the door is closed; the cycle will not start.

Door Status Detection Fault

E41

Washer-dryer intermittently reports a door error during a cycle; it may pause unexpectedly.

Intermittent Door Interlock Signal

E60

Washer-dryer shows a general heating system error; this may affect wash or dry heating.

Generic Heating System Fault

H1

Washer-dryer displays H1 and stops heating during the wash cycle; water remains cold.

Wash NTC Sensor Fault

H2

Washer-dryer displays H2; water overheats or the cycle aborts due to high temperature.

Wash Overheating / NTC Calibration Fault

H3

Washer-dryer displays H3; the motor does not run or runs erratically.

Motor Overcurrent / Overload Fault

H4

Washer-dryer displays H4; the drying cycle stops prematurely with little or no heat.

Dryer Overheat / Thermal Cut-Out Trip

H5

Washer-dryer displays H5; the drying system does not start or stops quickly.

Dryer Heater Control Fault

Symptom

Washer-dryer does not drain fully; a small amount of water remains in the drum after the cycle.

Partial Drain / Pump Performance Issue

Symptom

Washer-dryer door is stuck locked even though the machine is off and empty.

Mechanical Door Lock Jam

Symptom

Washer-dryer drum does not turn at all in wash or spin, but no error code is shown.

Drive Belt or Motor Failure

Symptom

Washer-dryer drying cycle runs, but clothes remain damp or take a very long time to dry.

Poor Drying Performance

Symptom

Washer-dryer emits a burning smell during wash or dry cycles.

Overheating Component or Electrical Insulation Failure

Symptom

Washer-dryer has a persistent musty or moldy odor inside the drum.

Biofilm and Detergent Residue Build-Up

Symptom

Washer-dryer intermittently trips the household circuit breaker or RCD.

Electrical Insulation / Earth Leakage Fault

Symptom

Washer-dryer leaks water from the front during wash or rinse.

Door Seal (Gasket) Leak

Symptom

Washer-dryer leaks water from the rear or underneath during operation.

Internal Hose or Tub Leak

Symptom

Washer-dryer leaves clothes very wet at the end of the cycle, even though it appears to spin.

Ineffective Spin / Low Spin Speed

Symptom

Washer-dryer leaves detergent residues or white streaks on clothes.

Poor Rinsing / Detergent Dispensing Issue

Symptom

Washer-dryer makes loud banging or knocking noises during spin.

Suspension / Shock Absorber Wear

Symptom

Washer-dryer makes scraping or metallic noises when turning the drum.

Foreign Object Between Drum and Tub

Symptom

Washer-dryer powers on, but buttons or the dial do not respond.

User Interface / Control Panel Fault

Symptom

Washer-dryer produces a high-pitched squeal or grinding noise when spinning.

Drum Bearing or Drive Pulley Wear

Symptom

Washer-dryer vibrates excessively and walks across the floor during spin.

Excessive Vibration / Installation Fault

Symptom

Washer-dryer will not start; all lights are off and the display is blank.

No Power / Mains Supply Fault