Blomberg Washer-Dryer Combos Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E01
Washer-dryer will not start; the door lock symbol flashes and the cycle will not begin.
Door Lock Failure
E02
Washer-dryer does not fill with water or fills very slowly; E02 is displayed shortly after cycle start.
Water Inlet Timeout / Fill Fault
E03
Washer-dryer does not drain; water remains in the drum and E03 is displayed.
Drain Pump Fault / Drain Timeout
E04
Washer-dryer overfills or shows E04; the water level is too high or water continuously enters the drum.
Overfill / Water Level Sensor Fault
E05
Washer-dryer does not heat water during wash; cycles run cold and E05 appears.
Wash Heater Circuit Fault
E06
Washer-dryer stops with E06; motor does not turn, or drum will not rotate.
Drive Motor / Tachometer Fault
E07
Washer-dryer displays E07 and will not spin at high speed; the drum may tumble slowly only.
Imbalance / Spin Protection Fault
E08
Washer-dryer shows E08; dryer function does not start or stops shortly after starting.
Dryer Fan / Blower Motor Fault
E09
Washer-dryer displays E09; dryer does not heat, and clothes remain wet after the drying cycle.
Dryer Heater Circuit Fault
E10
Washer-dryer shows E10; water remains in the drum at the end of the drying cycle, and clothes feel damp and steamy.
Condenser / Drying System Water Circuit Fault
E11
Washer-dryer displays E11; the door will not unlock at the end of the cycle even though the drum is empty.
Door Unlock Failure
E12
Washer-dryer shows E12; communication error between the main control board and the user interface panel.
Communication / UI Control Fault
E13
Washer-dryer displays E13; water detected in the base tray, or the anti-flood device is activated.
Leak / Anti-Flood Protection Activated
E14
Washer-dryer shows E14; NTC sensor error for wash temperature.
Wash Temperature Sensor (NTC) Fault
E15
Washer-dryer displays E15; dryer temperature sensor error.
Dryer NTC Sensor Fault
E16
Washer-dryer displays E16; water inlet valve triac or control fault.
Inlet Valve Control Circuit Failure
E17
Washer-dryer displays E17; motor triac or drive circuit error.
Motor Control Circuit Failure
E18
Washer-dryer displays E18; drain pump triac or control fault.
Drain Pump Control Circuit Failure
E19
Washer-dryer displays E19; EEPROM or configuration error.
Control Board Memory / Configuration Fault
E20
Washer-dryer displays E20; drying time too long or dryer not completing within the expected time.
Drying Efficiency / Moisture Sensing Fault
Symptom
Detergent remains in the drawer after a wash; poor rinsing performance.
Detergent Dispenser / Inlet Flow Issue
Symptom
Dryer cycle takes excessively long; the drum and door feel very hot.
Restricted Dryer Airflow / Overheating
Symptom
Washer-dryer combo will not power on; no lights or display response.
No Power / Mains Supply Fault
Symptom
Washer-dryer displays the time remaining, but the cycle finishes much earlier or later than expected.
Cycle Time Miscalculation / Sensor Feedback Issue
Symptom
Washer-dryer does not start cycle; display is on but the Start/Pause button does nothing.
User Interface / Start Circuit Fault
Symptom
Washer-dryer does not take fabric softener from the dispenser.
Softener Siphon / Dispenser Fault
Symptom
Washer-dryer door glass becomes extremely hot during drying.
Dryer Overheating at Door Area
Symptom
Washer-dryer door will not stay closed; the door pops open during cycle start.
Door Latch / Hinge Misalignment
Symptom
Washer-dryer drum does not turn during wash but can be rotated by hand.
Drive Belt Slipped or Broken
Symptom
Washer-dryer drum has visible play and scrapes against the door seal.
Drum Support / Spider Arm Failure
Symptom
Washer-dryer dryer cycle runs but clothes come out damp and cool.
No Heat in Dryer with Normal Airflow
Symptom
Washer-dryer emits a burning smell or smoke during operation.
Overheating / Electrical or Mechanical Friction
Symptom
Washer-dryer fills with water even when turned off.
Inlet Valve Not Closing
Symptom
Washer-dryer leaves clothes very wet at the end of the cycle; spin seems weak or does not reach full speed.
Poor Spin Performance / Imbalance or Drain Issue
Symptom
Washer-dryer makes a loud rumbling or roaring noise during spin.
Drum Bearing Wear / Failure
Symptom
Washer-dryer makes a squealing or screeching noise when the drum turns.
Drive Belt or Pulley Noise
Symptom
Washer-dryer produces a musty or moldy odor from the drum and during drying.
Biofilm / Mold Build-up in Drum and Air Ducts
Symptom
Washer-dryer produces loud banging or knocking during spin cycles.
Excessive Vibration / Suspension Fault
Symptom
Washer-dryer stops mid-cycle and the display goes blank, then comes back after a while.
Intermittent Power Loss / Overheating Control Board
Symptom
Washer-dryer vibrates excessively and moves across the floor during the spin cycle.
Installation / Floor Stability Issue
Symptom
Water leaking from the front of the washer-dryer around the door area.
Door Seal (Bellow) Leak
Symptom
Water leaking from the rear or bottom of the washer-dryer during wash or spin.
Internal Hose or Pump Leak
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E01 |
Washer-dryer will not start; the door lock symbol flashes and the cycle will not begin.
|
Door Lock Failure | View Details |
| E02 |
Washer-dryer does not fill with water or fills very slowly; E02 is displayed shortly after cycle start.
|
Water Inlet Timeout / Fill Fault | View Details |
| E03 |
Washer-dryer does not drain; water remains in the drum and E03 is displayed.
|
Drain Pump Fault / Drain Timeout | View Details |
| E04 |
Washer-dryer overfills or shows E04; the water level is too high or water continuously enters the drum.
|
Overfill / Water Level Sensor Fault | View Details |
| E05 |
Washer-dryer does not heat water during wash; cycles run cold and E05 appears.
|
Wash Heater Circuit Fault | View Details |
| E06 |
Washer-dryer stops with E06; motor does not turn, or drum will not rotate.
|
Drive Motor / Tachometer Fault | View Details |
| E07 |
Washer-dryer displays E07 and will not spin at high speed; the drum may tumble slowly only.
|
Imbalance / Spin Protection Fault | View Details |
| E08 |
Washer-dryer shows E08; dryer function does not start or stops shortly after starting.
|
Dryer Fan / Blower Motor Fault | View Details |
| E09 |
Washer-dryer displays E09; dryer does not heat, and clothes remain wet after the drying cycle.
|
Dryer Heater Circuit Fault | View Details |
| E10 |
Washer-dryer shows E10; water remains in the drum at the end of the drying cycle, and clothes feel damp and steamy.
|
Condenser / Drying System Water Circuit Fault | View Details |
| E11 |
Washer-dryer displays E11; the door will not unlock at the end of the cycle even though the drum is empty.
|
Door Unlock Failure | View Details |
| E12 |
Washer-dryer shows E12; communication error between the main control board and the user interface panel.
|
Communication / UI Control Fault | View Details |
| E13 |
Washer-dryer displays E13; water detected in the base tray, or the anti-flood device is activated.
|
Leak / Anti-Flood Protection Activated | View Details |
| E14 |
Washer-dryer shows E14; NTC sensor error for wash temperature.
|
Wash Temperature Sensor (NTC) Fault | View Details |
| E15 |
Washer-dryer displays E15; dryer temperature sensor error.
|
Dryer NTC Sensor Fault | View Details |
| E16 |
Washer-dryer displays E16; water inlet valve triac or control fault.
|
Inlet Valve Control Circuit Failure | View Details |
| E17 |
Washer-dryer displays E17; motor triac or drive circuit error.
|
Motor Control Circuit Failure | View Details |
| E18 |
Washer-dryer displays E18; drain pump triac or control fault.
|
Drain Pump Control Circuit Failure | View Details |
| E19 |
Washer-dryer displays E19; EEPROM or configuration error.
|
Control Board Memory / Configuration Fault | View Details |
| E20 |
Washer-dryer displays E20; drying time too long or dryer not completing within the expected time.
|
Drying Efficiency / Moisture Sensing Fault | View Details |
| – |
Detergent remains in the drawer after a wash; poor rinsing performance.
|
Detergent Dispenser / Inlet Flow Issue | View Details |
| – |
Dryer cycle takes excessively long; the drum and door feel very hot.
|
Restricted Dryer Airflow / Overheating | View Details |
| – |
Washer-dryer combo will not power on; no lights or display response.
|
No Power / Mains Supply Fault | View Details |
| – |
Washer-dryer displays the time remaining, but the cycle finishes much earlier or later than expected.
|
Cycle Time Miscalculation / Sensor Feedback Issue | View Details |
| – |
Washer-dryer does not start cycle; display is on but the Start/Pause button does nothing.
|
User Interface / Start Circuit Fault | View Details |
| – |
Washer-dryer does not take fabric softener from the dispenser.
|
Softener Siphon / Dispenser Fault | View Details |
| – |
Washer-dryer door glass becomes extremely hot during drying.
|
Dryer Overheating at Door Area | View Details |
| – |
Washer-dryer door will not stay closed; the door pops open during cycle start.
|
Door Latch / Hinge Misalignment | View Details |
| – |
Washer-dryer drum does not turn during wash but can be rotated by hand.
|
Drive Belt Slipped or Broken | View Details |
| – |
Washer-dryer drum has visible play and scrapes against the door seal.
|
Drum Support / Spider Arm Failure | View Details |
| – |
Washer-dryer dryer cycle runs but clothes come out damp and cool.
|
No Heat in Dryer with Normal Airflow | View Details |
| – |
Washer-dryer emits a burning smell or smoke during operation.
|
Overheating / Electrical or Mechanical Friction | View Details |
| – |
Washer-dryer fills with water even when turned off.
|
Inlet Valve Not Closing | View Details |
| – |
Washer-dryer leaves clothes very wet at the end of the cycle; spin seems weak or does not reach full speed.
|
Poor Spin Performance / Imbalance or Drain Issue | View Details |
| – |
Washer-dryer makes a loud rumbling or roaring noise during spin.
|
Drum Bearing Wear / Failure | View Details |
| – |
Washer-dryer makes a squealing or screeching noise when the drum turns.
|
Drive Belt or Pulley Noise | View Details |
| – |
Washer-dryer produces a musty or moldy odor from the drum and during drying.
|
Biofilm / Mold Build-up in Drum and Air Ducts | View Details |
| – |
Washer-dryer produces loud banging or knocking during spin cycles.
|
Excessive Vibration / Suspension Fault | View Details |
| – |
Washer-dryer stops mid-cycle and the display goes blank, then comes back after a while.
|
Intermittent Power Loss / Overheating Control Board | View Details |
| – |
Washer-dryer vibrates excessively and moves across the floor during the spin cycle.
|
Installation / Floor Stability Issue | View Details |
| – |
Water leaking from the front of the washer-dryer around the door area.
|
Door Seal (Bellow) Leak | View Details |
| – |
Water leaking from the rear or bottom of the washer-dryer during wash or spin.
|
Internal Hose or Pump Leak | View Details |
No matching codes found
Advertisements