Equator
Equator Washer-Dryer Combos Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E1
Washer-dryer combo will not fill with water; cycle starts then quickly stops and displays E1.
Water Inlet Timeout / No Fill
E10
Washer-dryer combo shows E10 and will not start; the control panel may be unresponsive or erratic.
Main Control Board Communication / Internal Fault
E11
Washer-dryer combo displays E11; this is often associated with motor speed sensing or tachometer issues.
Motor Tachometer / Speed Sensor Fault
E12
Washer-dryer combo shows E12 and may stop mid-cycle; this is often related to overheating or temperature sensor issues in drying mode.
Dryer Temperature Sensor / Overheat Fault
E13
Washer-dryer combo displays E13; this may be associated with the door not unlocking at the end of a cycle.
Door Unlock Failure
E14
Washer-dryer combo shows E14, often related to an NTC sensor fault in the wash cycle (water temperature sensing).
Wash Temperature Sensor (NTC) Fault
E15
Washer-dryer combo displays E15, which may be associated with communication issues between the user interface and the main board.
User Interface / Main Board Communication Error
E16
Washer-dryer combo shows E16, which may be related to door open detection during a cycle.
Door Open Detection Fault
E17
Washer-dryer combo displays E17, often associated with low water pressure or slow fill.
Low Water Pressure / Slow Fill Fault
E18
Washer-dryer combo shows E18, which may be related to drain pump overcurrent or blockage.
Drain Pump Overload / Blockage
E19
Washer-dryer combo displays E19, often associated with an internal memory or configuration error.
Control Board Configuration / EEPROM Fault
E2
Washer-dryer combo will not drain; water remains in drum and E2 is displayed.
Drain Pump Failure / Drain Timeout
E20
Washer-dryer combo shows E20, which may be related to overheating of the motor or electronics.
Motor / Electronics Overheat Protection
E3
Washer-dryer combo drum does not spin or tumble; E3 appears during wash or spin.
Motor Drive Fault / Motor Not Running
E4
Washer-dryer combo displays E4 and stops; this often occurs during the spin cycle with heavy or small loads.
Unbalanced Load / Out-of-Balance Detection
E5
Washer-dryer combo does not heat water; cycles run cold, and E5 appears on some models.
Water Heating Fault
E6
Washer-dryer combo does not heat or dry clothes in drying mode; E6 appears during the dry cycle.
Dryer Heating Fault
E7
Washer-dryer combo displays E7 and will not start or stops mid-cycle; the door may not lock properly.
Door Lock / Door Switch Fault
E8
Washer-dryer combo shows E8 and stops; this is often associated with water level issues (overfill or sensor error).
Water Level Sensor / Pressure Switch Fault
E9
Washer-dryer combo displays E9 and may stop filling or draining; this is sometimes associated with overflow or leak detection.
Overflow / Leak Detection Fault
Symptom
Washer-dryer combo display and lights flicker or reset during operation.
Intermittent Power / Voltage Drop
Symptom
Washer-dryer combo door will not open at the end of the cycle, and no error code is displayed.
Door Stuck / Lock Not Releasing
Symptom
Washer-dryer combo drum does not tumble during wash but can spin at high speed.
Wash Agitation / Tumble Failure
Symptom
Washer-dryer combo emits a moldy or musty odor from the drum.
Biofilm / Mold Growth in Drum and Hoses
Symptom
Washer-dryer combo fills and agitates but will not spin; clothes remain very wet at the end of the cycle.
No Spin / Spin Cycle Failure
Symptom
Washer-dryer combo is extremely noisy during spin, with banging or thumping sounds from the drum.
Excessive Vibration / Suspension Failure
Symptom
Washer-dryer combo leaks water from the front door area during the wash cycle.
Door Gasket / Boot Seal Leak
Symptom
Washer-dryer combo leaks water from the rear or bottom during the wash or drain cycle.
Internal Hose / Pump Leak
Symptom
Washer-dryer combo leaves clothes very wet after the dry cycle, indicating poor drying performance but no error code.
Poor Drying / Condenser Inefficiency
Symptom
Washer-dryer combo leaves detergent residue or white streaks on clothes.
Poor Rinsing / Detergent Residue
Symptom
Washer-dryer combo makes a clicking or rattling noise from the pump area even when not draining.
Foreign Object in Pump / Intermittent Pump Noise
Symptom
Washer-dryer combo makes a loud grinding or rumbling noise during spin; the noise increases with speed.
Drum Bearing / Spider Arm Failure
Symptom
Washer-dryer combo powers on but will not start any cycle; pressing Start does nothing.
Start Circuit / Control Lock Issue
Symptom
Washer-dryer combo produces a burning smell during the dry cycle.
Overheating / Lint on Heater
Symptom
Washer-dryer combo produces a high-pitched squeal during spin.
Belt / Pulley Squeal
Symptom
Washer-dryer combo takes much longer than expected to complete cycles.
Extended Cycle Time / Sensor Misread
Symptom
Washer-dryer combo vibrates excessively and walks across the floor during spin.
Severe Vibration / Installation Issue
Symptom
Washer-dryer combo will not power on at all; no lights or display response.
No Power / Dead Appliance
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E1 |
Washer-dryer combo will not fill with water; cycle starts then quickly stops and displays E1.
|
Water Inlet Timeout / No Fill | View Details |
| E10 |
Washer-dryer combo shows E10 and will not start; the control panel may be unresponsive or erratic.
|
Main Control Board Communication / Internal Fault | View Details |
| E11 |
Washer-dryer combo displays E11; this is often associated with motor speed sensing or tachometer issues.
|
Motor Tachometer / Speed Sensor Fault | View Details |
| E12 |
Washer-dryer combo shows E12 and may stop mid-cycle; this is often related to overheating or temperature sensor issues in drying mode.
|
Dryer Temperature Sensor / Overheat Fault | View Details |
| E13 |
Washer-dryer combo displays E13; this may be associated with the door not unlocking at the end of a cycle.
|
Door Unlock Failure | View Details |
| E14 |
Washer-dryer combo shows E14, often related to an NTC sensor fault in the wash cycle (water temperature sensing).
|
Wash Temperature Sensor (NTC) Fault | View Details |
| E15 |
Washer-dryer combo displays E15, which may be associated with communication issues between the user interface and the main board.
|
User Interface / Main Board Communication Error | View Details |
| E16 |
Washer-dryer combo shows E16, which may be related to door open detection during a cycle.
|
Door Open Detection Fault | View Details |
| E17 |
Washer-dryer combo displays E17, often associated with low water pressure or slow fill.
|
Low Water Pressure / Slow Fill Fault | View Details |
| E18 |
Washer-dryer combo shows E18, which may be related to drain pump overcurrent or blockage.
|
Drain Pump Overload / Blockage | View Details |
| E19 |
Washer-dryer combo displays E19, often associated with an internal memory or configuration error.
|
Control Board Configuration / EEPROM Fault | View Details |
| E2 |
Washer-dryer combo will not drain; water remains in drum and E2 is displayed.
|
Drain Pump Failure / Drain Timeout | View Details |
| E20 |
Washer-dryer combo shows E20, which may be related to overheating of the motor or electronics.
|
Motor / Electronics Overheat Protection | View Details |
| E3 |
Washer-dryer combo drum does not spin or tumble; E3 appears during wash or spin.
|
Motor Drive Fault / Motor Not Running | View Details |
| E4 |
Washer-dryer combo displays E4 and stops; this often occurs during the spin cycle with heavy or small loads.
|
Unbalanced Load / Out-of-Balance Detection | View Details |
| E5 |
Washer-dryer combo does not heat water; cycles run cold, and E5 appears on some models.
|
Water Heating Fault | View Details |
| E6 |
Washer-dryer combo does not heat or dry clothes in drying mode; E6 appears during the dry cycle.
|
Dryer Heating Fault | View Details |
| E7 |
Washer-dryer combo displays E7 and will not start or stops mid-cycle; the door may not lock properly.
|
Door Lock / Door Switch Fault | View Details |
| E8 |
Washer-dryer combo shows E8 and stops; this is often associated with water level issues (overfill or sensor error).
|
Water Level Sensor / Pressure Switch Fault | View Details |
| E9 |
Washer-dryer combo displays E9 and may stop filling or draining; this is sometimes associated with overflow or leak detection.
|
Overflow / Leak Detection Fault | View Details |
| – |
Washer-dryer combo display and lights flicker or reset during operation.
|
Intermittent Power / Voltage Drop | View Details |
| – |
Washer-dryer combo door will not open at the end of the cycle, and no error code is displayed.
|
Door Stuck / Lock Not Releasing | View Details |
| – |
Washer-dryer combo drum does not tumble during wash but can spin at high speed.
|
Wash Agitation / Tumble Failure | View Details |
| – |
Washer-dryer combo emits a moldy or musty odor from the drum.
|
Biofilm / Mold Growth in Drum and Hoses | View Details |
| – |
Washer-dryer combo fills and agitates but will not spin; clothes remain very wet at the end of the cycle.
|
No Spin / Spin Cycle Failure | View Details |
| – |
Washer-dryer combo is extremely noisy during spin, with banging or thumping sounds from the drum.
|
Excessive Vibration / Suspension Failure | View Details |
| – |
Washer-dryer combo leaks water from the front door area during the wash cycle.
|
Door Gasket / Boot Seal Leak | View Details |
| – |
Washer-dryer combo leaks water from the rear or bottom during the wash or drain cycle.
|
Internal Hose / Pump Leak | View Details |
| – |
Washer-dryer combo leaves clothes very wet after the dry cycle, indicating poor drying performance but no error code.
|
Poor Drying / Condenser Inefficiency | View Details |
| – |
Washer-dryer combo leaves detergent residue or white streaks on clothes.
|
Poor Rinsing / Detergent Residue | View Details |
| – |
Washer-dryer combo makes a clicking or rattling noise from the pump area even when not draining.
|
Foreign Object in Pump / Intermittent Pump Noise | View Details |
| – |
Washer-dryer combo makes a loud grinding or rumbling noise during spin; the noise increases with speed.
|
Drum Bearing / Spider Arm Failure | View Details |
| – |
Washer-dryer combo powers on but will not start any cycle; pressing Start does nothing.
|
Start Circuit / Control Lock Issue | View Details |
| – |
Washer-dryer combo produces a burning smell during the dry cycle.
|
Overheating / Lint on Heater | View Details |
| – |
Washer-dryer combo produces a high-pitched squeal during spin.
|
Belt / Pulley Squeal | View Details |
| – |
Washer-dryer combo takes much longer than expected to complete cycles.
|
Extended Cycle Time / Sensor Misread | View Details |
| – |
Washer-dryer combo vibrates excessively and walks across the floor during spin.
|
Severe Vibration / Installation Issue | View Details |
| – |
Washer-dryer combo will not power on at all; no lights or display response.
|
No Power / Dead Appliance | View Details |
No matching codes found
Advertisements