Hisense Washer-Dryer Combos Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E1
Washer-dryer does not fill with water, the cycle will not start, and E1 is displayed on the panel.
Water Inlet Timeout / No Fill
E10
The washer-dryer does not heat during the drying cycle, clothes come out wet and cold, and E10 is displayed.
Dryer Heating System Fault
E11
The drying cycle runs but takes excessively long, clothes remain damp, and E11 is displayed.
Dryer Airflow / Moisture Sensing Fault
E12
The washer-dryer displays E12 and may stop, often associated with communication issues between control boards.
Communication Error Between Main PCB and Inverter/Interface
E13
Washer-dryer displays E13, often related to the door not unlocking at the end of a cycle.
Door Unlock Fault
E14
Washer-dryer displays E14, often associated with an NTC sensor error in the wash circuit.
Wash Temperature Sensor (NTC) Fault
E15
Washer-dryer displays E15, often related to the dryer temperature sensor.
Dryer Temperature Sensor (NTC) Fault
E16
Washer-dryer displays E16 and may stop, often related to drainage during drying or a condenser system issue.
Condenser / Drying Drain System Fault
E17
Washer-dryer displays E17, often associated with low water pressure or a slow fill.
Low Water Pressure / Slow Fill Detection
E18
Washer-dryer displays E18, often related to a drain timeout or partial drain during drying.
Partial Drain / Drain Timeout
E19
Washer-dryer displays E19, often associated with an internal memory or configuration error.
EEPROM / Configuration Fault
E2
Washer-dryer does not drain water, the drum remains full, and E2 is displayed.
Drain Pump Failure / Drain Timeout
E20
Washer-dryer displays E20, often related to motor overheating or overcurrent.
Motor Overload / Overheat Protection
E21
Washer-dryer displays E21, often associated with the door being open during drying or washing.
Door Open Detection During Operation
E22
Washer-dryer displays E22, often related to the dryer fan or airflow monitoring.
Dryer Fan / Airflow Fault
E23
Washer-dryer displays E23, often associated with internal leak detection or water in the base tray.
Leak Detected / Anti-Flood Protection
E24
Washer-dryer shows E24, often related to overheating in the drying circuit.
Dryer Overheat / High Temperature Cut-Out
E25
Washer-dryer displays E25, often associated with spin speed detection or the final spin not being achieved.
Spin Speed Not Reached / Spin Control Fault
E3
Washer-dryer drum does not spin or tumble; E3 is displayed during wash or spin.
Motor Drive Fault / Motor Unable to Start
E4
The washer-dryer stops and displays E4, often during spinning, with the drum heavily loaded on one side.
Unbalanced Load / Out-of-Balance Protection
E5
The washer-dryer stops heating water, cycles run cold, and E5 is displayed.
Water Heating Fault
E6
The washer-dryer door will not lock or the cycle will not start; E6 is displayed.
Door Lock / Interlock Failure
E7
The washer-dryer displays E7 and may not start or may overfill/underfill; the water level seems incorrect.
Water Level Sensor / Pressure Switch Fault
E8
The washer-dryer stops mid-cycle and displays E8, often related to motor speed sensing.
Motor Tachometer / Speed Sensor Error
E9
The washer-dryer displays E9 and may stop, often associated with an abnormal water level or overflow.
Overflow / Overfill Protection Triggered
Symptom
Washer-dryer causes the circuit breaker or RCD to trip during operation.
Electrical Short or Ground Fault.
Symptom
Washer-dryer combo will not power on at all; no lights or display.
No Power / Dead Appliance
Symptom
Washer-dryer display works, but buttons respond intermittently or select the wrong function.
User Interface Keypad / Touch Control Fault.
Symptom
Washer-dryer does not dry clothes effectively; clothes come out damp and cool.
Poor Drying Performance.
Symptom
Washer-dryer door is stuck locked at the end of the cycle; no error code is shown.
Door Lock Stuck / Mechanical Jam.
Symptom
Washer-dryer drum does not tumble during wash, but it can drain and spin.
Wash Agitation / Tumble Failure
Symptom
Washer-dryer emits a burning smell during operation.
Overheating Component or Friction
Symptom
Washer-dryer emits a high-pitched squealing or screeching noise during spin.
Drive Belt or Pulley Noise.
Symptom
Washer-dryer fills and agitates but will not spin at the end of the cycle.
No Spin / Spin Inhibit Condition
Symptom
Washer-dryer has a strong musty or moldy odor inside the drum.
Biofilm / Mold Build-Up in Drum and Tub.
Symptom
Washer-dryer leaks water from the front door area during the wash cycle.
Door Seal (Gasket) Leak
Symptom
Washer-dryer leaks water from underneath the machine.
Internal Hose or Pump Leak
Symptom
Washer-dryer leaves clothes very wet at the end of the cycle, even though it appears to spin.
Poor Extraction / Low Final Spin Performance.
Symptom
Washer-dryer leaves detergent or softener residue in the drawer or on clothes.
Detergent Dispensing / Rinse-In Fault.
Symptom
Washer-dryer makes loud banging or knocking noises during spin.
Excessive Vibration / Suspension or Bearing Fault
Symptom
Washer-dryer powers on but will not start any cycle; the Start button is unresponsive.
User Interface / Control Lock or Start Circuit Fault
Symptom
Washer-dryer produces a grinding or scraping noise when the drum turns.
Foreign Object in Drum or Bearing Failure.
Symptom
Washer-dryer takes much longer than the displayed time to complete cycles.
Cycle Time Extension Due to Sensing.
Symptom
Washer-dryer vibrates excessively and moves across the floor during spin.
Severe Vibration / Installation Fault
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E1 |
Washer-dryer does not fill with water, the cycle will not start, and E1 is displayed on the panel.
|
Water Inlet Timeout / No Fill | View Details |
| E10 |
The washer-dryer does not heat during the drying cycle, clothes come out wet and cold, and E10 is displayed.
|
Dryer Heating System Fault | View Details |
| E11 |
The drying cycle runs but takes excessively long, clothes remain damp, and E11 is displayed.
|
Dryer Airflow / Moisture Sensing Fault | View Details |
| E12 |
The washer-dryer displays E12 and may stop, often associated with communication issues between control boards.
|
Communication Error Between Main PCB and Inverter/Interface | View Details |
| E13 |
Washer-dryer displays E13, often related to the door not unlocking at the end of a cycle.
|
Door Unlock Fault | View Details |
| E14 |
Washer-dryer displays E14, often associated with an NTC sensor error in the wash circuit.
|
Wash Temperature Sensor (NTC) Fault | View Details |
| E15 |
Washer-dryer displays E15, often related to the dryer temperature sensor.
|
Dryer Temperature Sensor (NTC) Fault | View Details |
| E16 |
Washer-dryer displays E16 and may stop, often related to drainage during drying or a condenser system issue.
|
Condenser / Drying Drain System Fault | View Details |
| E17 |
Washer-dryer displays E17, often associated with low water pressure or a slow fill.
|
Low Water Pressure / Slow Fill Detection | View Details |
| E18 |
Washer-dryer displays E18, often related to a drain timeout or partial drain during drying.
|
Partial Drain / Drain Timeout | View Details |
| E19 |
Washer-dryer displays E19, often associated with an internal memory or configuration error.
|
EEPROM / Configuration Fault | View Details |
| E2 |
Washer-dryer does not drain water, the drum remains full, and E2 is displayed.
|
Drain Pump Failure / Drain Timeout | View Details |
| E20 |
Washer-dryer displays E20, often related to motor overheating or overcurrent.
|
Motor Overload / Overheat Protection | View Details |
| E21 |
Washer-dryer displays E21, often associated with the door being open during drying or washing.
|
Door Open Detection During Operation | View Details |
| E22 |
Washer-dryer displays E22, often related to the dryer fan or airflow monitoring.
|
Dryer Fan / Airflow Fault | View Details |
| E23 |
Washer-dryer displays E23, often associated with internal leak detection or water in the base tray.
|
Leak Detected / Anti-Flood Protection | View Details |
| E24 |
Washer-dryer shows E24, often related to overheating in the drying circuit.
|
Dryer Overheat / High Temperature Cut-Out | View Details |
| E25 |
Washer-dryer displays E25, often associated with spin speed detection or the final spin not being achieved.
|
Spin Speed Not Reached / Spin Control Fault | View Details |
| E3 |
Washer-dryer drum does not spin or tumble; E3 is displayed during wash or spin.
|
Motor Drive Fault / Motor Unable to Start | View Details |
| E4 |
The washer-dryer stops and displays E4, often during spinning, with the drum heavily loaded on one side.
|
Unbalanced Load / Out-of-Balance Protection | View Details |
| E5 |
The washer-dryer stops heating water, cycles run cold, and E5 is displayed.
|
Water Heating Fault | View Details |
| E6 |
The washer-dryer door will not lock or the cycle will not start; E6 is displayed.
|
Door Lock / Interlock Failure | View Details |
| E7 |
The washer-dryer displays E7 and may not start or may overfill/underfill; the water level seems incorrect.
|
Water Level Sensor / Pressure Switch Fault | View Details |
| E8 |
The washer-dryer stops mid-cycle and displays E8, often related to motor speed sensing.
|
Motor Tachometer / Speed Sensor Error | View Details |
| E9 |
The washer-dryer displays E9 and may stop, often associated with an abnormal water level or overflow.
|
Overflow / Overfill Protection Triggered | View Details |
| – |
Washer-dryer causes the circuit breaker or RCD to trip during operation.
|
Electrical Short or Ground Fault. | View Details |
| – |
Washer-dryer combo will not power on at all; no lights or display.
|
No Power / Dead Appliance | View Details |
| – |
Washer-dryer display works, but buttons respond intermittently or select the wrong function.
|
User Interface Keypad / Touch Control Fault. | View Details |
| – |
Washer-dryer does not dry clothes effectively; clothes come out damp and cool.
|
Poor Drying Performance. | View Details |
| – |
Washer-dryer door is stuck locked at the end of the cycle; no error code is shown.
|
Door Lock Stuck / Mechanical Jam. | View Details |
| – |
Washer-dryer drum does not tumble during wash, but it can drain and spin.
|
Wash Agitation / Tumble Failure | View Details |
| – |
Washer-dryer emits a burning smell during operation.
|
Overheating Component or Friction | View Details |
| – |
Washer-dryer emits a high-pitched squealing or screeching noise during spin.
|
Drive Belt or Pulley Noise. | View Details |
| – |
Washer-dryer fills and agitates but will not spin at the end of the cycle.
|
No Spin / Spin Inhibit Condition | View Details |
| – |
Washer-dryer has a strong musty or moldy odor inside the drum.
|
Biofilm / Mold Build-Up in Drum and Tub. | View Details |
| – |
Washer-dryer leaks water from the front door area during the wash cycle.
|
Door Seal (Gasket) Leak | View Details |
| – |
Washer-dryer leaks water from underneath the machine.
|
Internal Hose or Pump Leak | View Details |
| – |
Washer-dryer leaves clothes very wet at the end of the cycle, even though it appears to spin.
|
Poor Extraction / Low Final Spin Performance. | View Details |
| – |
Washer-dryer leaves detergent or softener residue in the drawer or on clothes.
|
Detergent Dispensing / Rinse-In Fault. | View Details |
| – |
Washer-dryer makes loud banging or knocking noises during spin.
|
Excessive Vibration / Suspension or Bearing Fault | View Details |
| – |
Washer-dryer powers on but will not start any cycle; the Start button is unresponsive.
|
User Interface / Control Lock or Start Circuit Fault | View Details |
| – |
Washer-dryer produces a grinding or scraping noise when the drum turns.
|
Foreign Object in Drum or Bearing Failure. | View Details |
| – |
Washer-dryer takes much longer than the displayed time to complete cycles.
|
Cycle Time Extension Due to Sensing. | View Details |
| – |
Washer-dryer vibrates excessively and moves across the floor during spin.
|
Severe Vibration / Installation Fault | View Details |
No matching codes found
Advertisements