Hoover Washer-Dryer Combos Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E01
Washer-dryer will not start; display shows E01, and the door remains locked or will not lock.
Door Lock Circuit Failure
E02
Washer-dryer does not fill with water or fills very slowly; E02 is displayed.
Water Inlet Timeout / Fill Fault
E03
Washer-dryer will not drain; cycle stops with water in the drum, and E03 is displayed.
Drain Pump Timeout / Drainage Fault
E04
Washer-dryer overfills or shows E04 shortly after starting fill; it may attempt to drain immediately.
Overfill / Pressure Switch Fault
E05
Washer-dryer stops during wash or rinse; E05 is displayed, and the water may be cold.
Heating Circuit Fault (Wash Heater)
E06
Washer-dryer stops or will not start spin; E06 is displayed, and it may not reach high spin speed.
Motor Tachometer / Speed Sensor Fault
E07
Washer-dryer shows E07 and may not spin or may stop mid-cycle; it is sometimes associated with door lock issues.
Door Lock / Motor Interlock Logic Fault
E08
Washer-dryer drum does not turn or turns erratically; E08 is displayed.
Motor Drive Fault / Triac Error
E09
Washer-dryer will not spin or wash; E09 displayed; sometimes accompanied by a tripped household breaker.
Motor Short Circuit / Power Module Fault
E10
Washer-dryer fails to start the drying cycle; E10 displayed.
Dryer Heating Circuit Fault
E11
Drying performance is very poor or stops early; E11 displayed.
Dryer Temperature Sensing Fault
E12
Washer-dryer shows E12 during drying; the drum may turn but there is no heat or the cycle aborts.
Dryer Fan / Airflow Fault
E13
Washer-dryer shows E13; this may be associated with water detected in the base or a leak during drying.
Leak Detection / Overflow in Base
E16
Washer-dryer shows E16; the door may not unlock at the end of the cycle.
Door Unlock Fault
E17
Washer-dryer shows E17; this is often related to water inlet or flow meter issues.
Water Flow Measurement Fault
E18
Washer-dryer shows E18; it may stop mid-cycle with water remaining.
Drain Time Exceeded / Partial Blockage
E20
Washer-dryer shows E20; it may not start or may stop with no drum movement.
General Motor Fault
E21
Washer-dryer shows E21; the drum may not turn or may turn only in one direction.
Motor Direction / Relay Fault
E22
Washer-dryer shows E22; often associated with the drying cycle not starting or aborting.
Dryer Condenser / Pump Fault (where fitted)
E23
Washer-dryer shows E23; this may be related to a drain pump triac or control issue.
Drain Pump Control Fault
E24
Washer-dryer shows E24; the appliance may not start or may stop unexpectedly.
Communication Fault Between Display and Main PCB
E25
Washer-dryer shows E25; this may be associated with sensor or analog input errors.
Analog Sensor Input Fault
E26
Washer-dryer shows E26; this is often linked to pressure sensor or water level issues.
Electronic Pressure Sensor Fault
E30
Washer-dryer shows E30; the appliance may not start or may stop due to door-related issues.
General Door System Fault
E40
Washer-dryer shows E40; the door symbol may flash, and the machine will not start.
Door Not Properly Closed / Door Lock Error
E41
Washer-dryer shows E41; the door appears closed, but the machine indicates it is open.
Door Open Signal Fault
E42
Washer-dryer shows E42; the door may remain locked or unlock unexpectedly.
Door Locking/Unlocking Control Fault
E50
Washer-dryer shows E50; this is a motor-related error, and the drum may not turn.
General Motor / Power Fault
Symptom
Washer-dryer combo will not power on at all; no lights or display.
No Mains Power / Control Board Supply Failure
Symptom
Washer-dryer does not spin or only performs slow spins; clothes come out very wet.
Spin Cycle Not Reaching High Speed
Symptom
Washer-dryer door will not open at the end of the cycle, but no error code is shown.
Door Lock Stuck Closed
Symptom
Washer-dryer emits a burning smell during the wash or spin cycle.
Overheating Motor or Belt Slippage
Symptom
Washer-dryer emits a strong, mouldy or musty smell from the drum.
Biofilm and Detergent Residue Build-up
Symptom
Washer-dryer fills and drains, but the drum does not turn during wash or spin.
Drive System Failure
Symptom
Washer-dryer leaks water from the front during the wash cycle.
Front Door Seal / Gasket Leak
Symptom
Washer-dryer leaks water from the rear or underneath during the wash cycle.
Internal Hose or Pump Leak
Symptom
Washer-dryer leaves clothes very wet after drying; drying performance is poor or takes too long.
Restricted Airflow / Inefficient Drying
Symptom
Washer-dryer leaves detergent or fabric softener in the drawer after the cycle.
Detergent Dispenser Flow Fault
Symptom
Washer-dryer leaves grey or black marks on clothes.
Contamination from Seal, Bearings, or Residue
Symptom
Washer-dryer makes a loud banging or knocking noise during the spin cycle; the machine moves across the floor.
Excessive Vibration / Suspension Fault
Symptom
Washer-dryer makes a very loud rumbling or grinding noise during the spin cycle.
Drum Bearing Failure
Symptom
Washer-dryer powers on but will not start any program; start button unresponsive.
User Interface / Control Lock Fault
Symptom
Washer-dryer stops during drying with water collecting in the drum.
Condenser Drainage / Pump Issue
Symptom
Washer-dryer trips the household circuit breaker or RCD during operation.
Earth Leakage / Short Circuit
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E01 |
Washer-dryer will not start; display shows E01, and the door remains locked or will not lock.
|
Door Lock Circuit Failure | View Details |
| E02 |
Washer-dryer does not fill with water or fills very slowly; E02 is displayed.
|
Water Inlet Timeout / Fill Fault | View Details |
| E03 |
Washer-dryer will not drain; cycle stops with water in the drum, and E03 is displayed.
|
Drain Pump Timeout / Drainage Fault | View Details |
| E04 |
Washer-dryer overfills or shows E04 shortly after starting fill; it may attempt to drain immediately.
|
Overfill / Pressure Switch Fault | View Details |
| E05 |
Washer-dryer stops during wash or rinse; E05 is displayed, and the water may be cold.
|
Heating Circuit Fault (Wash Heater) | View Details |
| E06 |
Washer-dryer stops or will not start spin; E06 is displayed, and it may not reach high spin speed.
|
Motor Tachometer / Speed Sensor Fault | View Details |
| E07 |
Washer-dryer shows E07 and may not spin or may stop mid-cycle; it is sometimes associated with door lock issues.
|
Door Lock / Motor Interlock Logic Fault | View Details |
| E08 |
Washer-dryer drum does not turn or turns erratically; E08 is displayed.
|
Motor Drive Fault / Triac Error | View Details |
| E09 |
Washer-dryer will not spin or wash; E09 displayed; sometimes accompanied by a tripped household breaker.
|
Motor Short Circuit / Power Module Fault | View Details |
| E10 |
Washer-dryer fails to start the drying cycle; E10 displayed.
|
Dryer Heating Circuit Fault | View Details |
| E11 |
Drying performance is very poor or stops early; E11 displayed.
|
Dryer Temperature Sensing Fault | View Details |
| E12 |
Washer-dryer shows E12 during drying; the drum may turn but there is no heat or the cycle aborts.
|
Dryer Fan / Airflow Fault | View Details |
| E13 |
Washer-dryer shows E13; this may be associated with water detected in the base or a leak during drying.
|
Leak Detection / Overflow in Base | View Details |
| E16 |
Washer-dryer shows E16; the door may not unlock at the end of the cycle.
|
Door Unlock Fault | View Details |
| E17 |
Washer-dryer shows E17; this is often related to water inlet or flow meter issues.
|
Water Flow Measurement Fault | View Details |
| E18 |
Washer-dryer shows E18; it may stop mid-cycle with water remaining.
|
Drain Time Exceeded / Partial Blockage | View Details |
| E20 |
Washer-dryer shows E20; it may not start or may stop with no drum movement.
|
General Motor Fault | View Details |
| E21 |
Washer-dryer shows E21; the drum may not turn or may turn only in one direction.
|
Motor Direction / Relay Fault | View Details |
| E22 |
Washer-dryer shows E22; often associated with the drying cycle not starting or aborting.
|
Dryer Condenser / Pump Fault (where fitted) | View Details |
| E23 |
Washer-dryer shows E23; this may be related to a drain pump triac or control issue.
|
Drain Pump Control Fault | View Details |
| E24 |
Washer-dryer shows E24; the appliance may not start or may stop unexpectedly.
|
Communication Fault Between Display and Main PCB | View Details |
| E25 |
Washer-dryer shows E25; this may be associated with sensor or analog input errors.
|
Analog Sensor Input Fault | View Details |
| E26 |
Washer-dryer shows E26; this is often linked to pressure sensor or water level issues.
|
Electronic Pressure Sensor Fault | View Details |
| E30 |
Washer-dryer shows E30; the appliance may not start or may stop due to door-related issues.
|
General Door System Fault | View Details |
| E40 |
Washer-dryer shows E40; the door symbol may flash, and the machine will not start.
|
Door Not Properly Closed / Door Lock Error | View Details |
| E41 |
Washer-dryer shows E41; the door appears closed, but the machine indicates it is open.
|
Door Open Signal Fault | View Details |
| E42 |
Washer-dryer shows E42; the door may remain locked or unlock unexpectedly.
|
Door Locking/Unlocking Control Fault | View Details |
| E50 |
Washer-dryer shows E50; this is a motor-related error, and the drum may not turn.
|
General Motor / Power Fault | View Details |
| – |
Washer-dryer combo will not power on at all; no lights or display.
|
No Mains Power / Control Board Supply Failure | View Details |
| – |
Washer-dryer does not spin or only performs slow spins; clothes come out very wet.
|
Spin Cycle Not Reaching High Speed | View Details |
| – |
Washer-dryer door will not open at the end of the cycle, but no error code is shown.
|
Door Lock Stuck Closed | View Details |
| – |
Washer-dryer emits a burning smell during the wash or spin cycle.
|
Overheating Motor or Belt Slippage | View Details |
| – |
Washer-dryer emits a strong, mouldy or musty smell from the drum.
|
Biofilm and Detergent Residue Build-up | View Details |
| – |
Washer-dryer fills and drains, but the drum does not turn during wash or spin.
|
Drive System Failure | View Details |
| – |
Washer-dryer leaks water from the front during the wash cycle.
|
Front Door Seal / Gasket Leak | View Details |
| – |
Washer-dryer leaks water from the rear or underneath during the wash cycle.
|
Internal Hose or Pump Leak | View Details |
| – |
Washer-dryer leaves clothes very wet after drying; drying performance is poor or takes too long.
|
Restricted Airflow / Inefficient Drying | View Details |
| – |
Washer-dryer leaves detergent or fabric softener in the drawer after the cycle.
|
Detergent Dispenser Flow Fault | View Details |
| – |
Washer-dryer leaves grey or black marks on clothes.
|
Contamination from Seal, Bearings, or Residue | View Details |
| – |
Washer-dryer makes a loud banging or knocking noise during the spin cycle; the machine moves across the floor.
|
Excessive Vibration / Suspension Fault | View Details |
| – |
Washer-dryer makes a very loud rumbling or grinding noise during the spin cycle.
|
Drum Bearing Failure | View Details |
| – |
Washer-dryer powers on but will not start any program; start button unresponsive.
|
User Interface / Control Lock Fault | View Details |
| – |
Washer-dryer stops during drying with water collecting in the drum.
|
Condenser Drainage / Pump Issue | View Details |
| – |
Washer-dryer trips the household circuit breaker or RCD during operation.
|
Earth Leakage / Short Circuit | View Details |
No matching codes found
Advertisements