Ikea Washer-Dryer Combos Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E01
Washer-dryer will not start a cycle; the display shows E01, and the door symbol may flash.
Door Lock Failure
E02
Washer-dryer does not fill with water or fills very slowly; E02 is displayed.
Water Inlet Timeout / Low Fill
E03
Washer-dryer does not drain water; the cycle stops with water in the drum, and E03 is displayed.
Drain Pump Failure / Drain Timeout
E04
Washer-dryer overfills or shows E04; water may be visible in the door glass above the normal level.
Overfill / Water Level Sensor Fault
E05
Washer-dryer stops during a wash cycle; water remains cold, and E05 is displayed.
Water Heating Failure
E06
Washer-dryer drum does not turn; E06 is displayed shortly after the cycle starts.
Motor Drive Fault
E07
Washer-dryer will not spin; E07 is displayed near the spin phase.
Unbalanced Load / Spin Protection Fault
E08
Washer-dryer stops during the drying cycle; E08 is displayed, and laundry remains wet.
Dryer Heating Circuit Fault
E09
Washer-dryer shows E09 and stops; this may be related to dryer function or internal communication.
Dryer Sensor / NTC Fault
E10
Washer-dryer displays E10 and will not start or stops mid-cycle.
Configuration / Communication Error
E11
Washer-dryer shows E11; the door may not unlock at the end of the cycle.
Door Unlock Fault
E12
Washer-dryer shows E12 during drying; clothes remain damp, and the cycle ends prematurely.
Dryer Moisture Sensing Fault
E13
Washer-dryer displays E13 and may stop with water in the base tray; a possible leak is detected.
Leak / Anti-Flood System Activated
E14
Washer-dryer shows E14; drying performance is poor or there is no heat.
Condenser / Airflow Blockage
E15
Washer-dryer shows E15; it may not start or may stop unexpectedly.
Power Supply / Voltage Error
E16
Washer-dryer shows E16; water remains in the drum, and the door may stay locked.
Drain / Siphon Error
E17
Washer-dryer shows E17; it is often associated with water inlet or flow meter issues.
Water Flow Meter Fault
E18
Washer-dryer shows E18; it may stop during a spin cycle or show abnormal drum speed behavior.
Motor Tachometer / Speed Sensing Fault
E19
Washer-dryer shows E19; this may be related to internal valve switching for wash/dry cycles.
Diverter Valve / Drying Water Valve Fault
E20
Washer-dryer shows E20; it may not start drying or may stop shortly after starting.
Dryer Pump / Condenser Water Pump Fault
Symptom
Detergent remains in the drawer after the wash cycle.
Detergent Drawer Water Flow Issue
Symptom
Washer-dryer combo leaks from the rear or underneath during wash or spin.
Internal Hose or Pump Leak
Symptom
Washer-dryer combo leaks water from the front door area during wash or rinse.
Door Gasket (Boot Seal) Leak
Symptom
Washer-dryer displays random lights or beeps without user input.
User Interface Glitch or Moisture Ingress
Symptom
Washer-dryer does not dry clothes properly; clothes come out damp after a full drying cycle.
Poor Drying Performance
Symptom
Washer-dryer door is difficult to open or close; it may require force.
Door Hinge or Latch Misalignment
Symptom
Washer-dryer drum does not turn during wash but can be turned by hand.
Drive Belt Slipped or Broken
Symptom
Washer-dryer emits a burning smell during wash or dry cycles.
Overheating Component or Belt Slippage
Symptom
Washer-dryer emits a loud humming sound but does not fill with water at the start of the cycle.
Water Inlet Valve Stuck or Blocked
Symptom
Washer-dryer fills and drains repeatedly without progressing in the cycle.
Pressure System or Siphoning Issue
Symptom
Washer-dryer leaves clothes smelling musty or moldy after washing.
Biofilm / Mold Build-up in Drum and Hoses
Symptom
Washer-dryer leaves clothes very wet at the end of the cycle (poor spin performance).
Spin Inefficiency / Drain or Load Issue
Symptom
Washer-dryer makes loud banging or knocking noises during spin.
Suspension or Drum Support Failure
Symptom
Washer-dryer produces a high-pitched squeal or grinding noise when spinning.
Drum Bearing or Drive Pulley Wear
Symptom
Washer-dryer stops mid-cycle, and the door remains locked with water inside, but no error code is displayed.
Intermittent Power or Control Fault
Symptom
Washer-dryer takes much longer than expected to complete cycles.
Extended Cycle Time / Sensor Compensation
Symptom
Washer-dryer vibrates excessively and "walks" across the floor during spin.
Excessive Vibration / Poor Installation
Symptom
Washer-dryer will not power on at all; no lights or display.
No Power / Dead Appliance
Symptom
Washer-dryer will not start; lights on but no response when pressing Start.
User Interface / Control Lock Issue
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E01 |
Washer-dryer will not start a cycle; the display shows E01, and the door symbol may flash.
|
Door Lock Failure | View Details |
| E02 |
Washer-dryer does not fill with water or fills very slowly; E02 is displayed.
|
Water Inlet Timeout / Low Fill | View Details |
| E03 |
Washer-dryer does not drain water; the cycle stops with water in the drum, and E03 is displayed.
|
Drain Pump Failure / Drain Timeout | View Details |
| E04 |
Washer-dryer overfills or shows E04; water may be visible in the door glass above the normal level.
|
Overfill / Water Level Sensor Fault | View Details |
| E05 |
Washer-dryer stops during a wash cycle; water remains cold, and E05 is displayed.
|
Water Heating Failure | View Details |
| E06 |
Washer-dryer drum does not turn; E06 is displayed shortly after the cycle starts.
|
Motor Drive Fault | View Details |
| E07 |
Washer-dryer will not spin; E07 is displayed near the spin phase.
|
Unbalanced Load / Spin Protection Fault | View Details |
| E08 |
Washer-dryer stops during the drying cycle; E08 is displayed, and laundry remains wet.
|
Dryer Heating Circuit Fault | View Details |
| E09 |
Washer-dryer shows E09 and stops; this may be related to dryer function or internal communication.
|
Dryer Sensor / NTC Fault | View Details |
| E10 |
Washer-dryer displays E10 and will not start or stops mid-cycle.
|
Configuration / Communication Error | View Details |
| E11 |
Washer-dryer shows E11; the door may not unlock at the end of the cycle.
|
Door Unlock Fault | View Details |
| E12 |
Washer-dryer shows E12 during drying; clothes remain damp, and the cycle ends prematurely.
|
Dryer Moisture Sensing Fault | View Details |
| E13 |
Washer-dryer displays E13 and may stop with water in the base tray; a possible leak is detected.
|
Leak / Anti-Flood System Activated | View Details |
| E14 |
Washer-dryer shows E14; drying performance is poor or there is no heat.
|
Condenser / Airflow Blockage | View Details |
| E15 |
Washer-dryer shows E15; it may not start or may stop unexpectedly.
|
Power Supply / Voltage Error | View Details |
| E16 |
Washer-dryer shows E16; water remains in the drum, and the door may stay locked.
|
Drain / Siphon Error | View Details |
| E17 |
Washer-dryer shows E17; it is often associated with water inlet or flow meter issues.
|
Water Flow Meter Fault | View Details |
| E18 |
Washer-dryer shows E18; it may stop during a spin cycle or show abnormal drum speed behavior.
|
Motor Tachometer / Speed Sensing Fault | View Details |
| E19 |
Washer-dryer shows E19; this may be related to internal valve switching for wash/dry cycles.
|
Diverter Valve / Drying Water Valve Fault | View Details |
| E20 |
Washer-dryer shows E20; it may not start drying or may stop shortly after starting.
|
Dryer Pump / Condenser Water Pump Fault | View Details |
| – |
Detergent remains in the drawer after the wash cycle.
|
Detergent Drawer Water Flow Issue | View Details |
| – |
Washer-dryer combo leaks from the rear or underneath during wash or spin.
|
Internal Hose or Pump Leak | View Details |
| – |
Washer-dryer combo leaks water from the front door area during wash or rinse.
|
Door Gasket (Boot Seal) Leak | View Details |
| – |
Washer-dryer displays random lights or beeps without user input.
|
User Interface Glitch or Moisture Ingress | View Details |
| – |
Washer-dryer does not dry clothes properly; clothes come out damp after a full drying cycle.
|
Poor Drying Performance | View Details |
| – |
Washer-dryer door is difficult to open or close; it may require force.
|
Door Hinge or Latch Misalignment | View Details |
| – |
Washer-dryer drum does not turn during wash but can be turned by hand.
|
Drive Belt Slipped or Broken | View Details |
| – |
Washer-dryer emits a burning smell during wash or dry cycles.
|
Overheating Component or Belt Slippage | View Details |
| – |
Washer-dryer emits a loud humming sound but does not fill with water at the start of the cycle.
|
Water Inlet Valve Stuck or Blocked | View Details |
| – |
Washer-dryer fills and drains repeatedly without progressing in the cycle.
|
Pressure System or Siphoning Issue | View Details |
| – |
Washer-dryer leaves clothes smelling musty or moldy after washing.
|
Biofilm / Mold Build-up in Drum and Hoses | View Details |
| – |
Washer-dryer leaves clothes very wet at the end of the cycle (poor spin performance).
|
Spin Inefficiency / Drain or Load Issue | View Details |
| – |
Washer-dryer makes loud banging or knocking noises during spin.
|
Suspension or Drum Support Failure | View Details |
| – |
Washer-dryer produces a high-pitched squeal or grinding noise when spinning.
|
Drum Bearing or Drive Pulley Wear | View Details |
| – |
Washer-dryer stops mid-cycle, and the door remains locked with water inside, but no error code is displayed.
|
Intermittent Power or Control Fault | View Details |
| – |
Washer-dryer takes much longer than expected to complete cycles.
|
Extended Cycle Time / Sensor Compensation | View Details |
| – |
Washer-dryer vibrates excessively and "walks" across the floor during spin.
|
Excessive Vibration / Poor Installation | View Details |
| – |
Washer-dryer will not power on at all; no lights or display.
|
No Power / Dead Appliance | View Details |
| – |
Washer-dryer will not start; lights on but no response when pressing Start.
|
User Interface / Control Lock Issue | View Details |
No matching codes found
Advertisements