Blomberg Washing Machines Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E01
Washer will not start cycle, door symbol flashes and cycle cancels shortly after pressing Start
Door Lock / Interlock Failure
E02
Washer does not fill with water or fills very slowly, then stops and displays E02
Water Inlet / Fill Fault
E03
Washer does not drain; water remains in the drum and E03 is displayed.
Drain Pump / Drainage Fault
E04
Washer overfills, water level is too high, or water leaks from the door, then stops with E04.
Overfill / Pressure System Fault
E05
Washer does not heat water; the cycle takes unusually long or stops with E05.
Heating Circuit Fault
E06
Washer drum does not rotate or struggles to turn; E06 is displayed during wash or spin.
Motor Drive Fault
E07
Washer attempts to spin but stops; it may make clicking sounds and E07 is displayed.
Tachometer / Motor Speed Feedback Fault
E08
Washer stops mid-cycle with E08; often associated with an unbalanced load or spin issues.
Unbalanced Load / Spin Protection Fault
E09
Washer stops and displays E09; often with no drum movement at all from the start of the cycle.
Inverter / Motor Power Module Fault (for inverter motor models)
E10
Washer does not fill within the expected time; E10 is displayed early in the cycle.
Water Fill Timeout
E11
Washer fills but then quickly drains or cannot maintain the water level; E11 is displayed.
Water Level / Pressure Sensor Fault
E12
Washer stops with E12; often during the heating phase, sometimes accompanied by lukewarm water.
NTC Temperature Sensor Fault
E13
Washer displays E13, often associated with water detected in the base tray or leak protection activation.
Leak / AquaStop Activation
E14
Washer shows E14 and will not start or complete a program, often related to control issues.
Main Control Board Communication / Internal Fault
E15
Washer displays E15, often with no response from buttons or erratic behavior.
User Interface / Display Board Fault
E16
Washer door will not unlock at the end of the cycle, E16 is displayed or the lock symbol remains on.
Door Unlock Fault
E17
Washer stops with E17, often during the spin cycle, sometimes accompanied by high vibration.
Excessive Vibration / Out-of-Balance Protection
E18
Washer shows E18 and does not drain or spin properly, sometimes intermittent.
Drain Pump Electrical Fault
E19
Washer displays E19, often related to detergent drawer or water distribution issues.
Detergent Drawer / Water Distribution Valve Fault
E20
Washer shows E20 and will not start or complete a cycle, often after power issues.
Power Supply / Voltage Fault
Symptom
Washer displays incorrect time remaining or random program behavior without specific error codes
Control Logic / Sensor Calibration Issues
Symptom
Washer does not take in fabric softener from the drawer
Softener Siphon / Drawer Flow Fault
Symptom
Washer door will not open at the end of the cycle, no error code shown
Door Stuck / Lock Not Releasing
Symptom
Washer fills and drains but drum does not turn at all during wash or spin
Complete Drum Drive Failure
Symptom
Washer fills with water even when switched off, slowly over time
Inlet Valve Not Closing Properly
Symptom
Washer has a bad odor inside the drum or from the detergent drawer
Biofilm / Mold and Bacteria Build-Up
Symptom
Washer hums but does not fill with water at the start of the cycle
Water Inlet Flow Restriction
Symptom
Washer is dead, no lights or display, and does not respond to the power button.
No Power / Dead Appliance
Symptom
Washer leaks water from the front door area during wash
Door Seal (Gasket) Leak
Symptom
Washer leaks water from underneath the machine
Internal Hose or Pump Leak
Symptom
Washer leaves clothes soaking wet at the end of the cycle
Poor Spin / Residual Water in Laundry
Symptom
Washer leaves detergent or fabric softener in the drawer at the end of the cycle
Poor Detergent Drawer Rinsing
Symptom
Washer makes loud banging or knocking noises during spin
Excessive Vibration / Suspension or Bearing Wear
Symptom
Washer powers on but will not start any program when Start/Pause is pressed.
Start Circuit / Program Inhibit Fault
Symptom
Washer produces a high-pitched squeal or grinding noise when spinning
Drum Bearing or Drive Pulley Fault
Symptom
Washer takes much longer than the displayed time to complete a cycle
Extended Cycle Time / Heating or Balance Issues
Symptom
Washer trips the household circuit breaker or RCD during operation
Electrical Short or Earth Leakage
Symptom
Washer vibrates excessively and "walks" across the floor during spin on a new installation
Installation / Transport Bolt Issue
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E01 |
Washer will not start cycle, door symbol flashes and cycle cancels shortly after pressing Start
|
Door Lock / Interlock Failure | View Details |
| E02 |
Washer does not fill with water or fills very slowly, then stops and displays E02
|
Water Inlet / Fill Fault | View Details |
| E03 |
Washer does not drain; water remains in the drum and E03 is displayed.
|
Drain Pump / Drainage Fault | View Details |
| E04 |
Washer overfills, water level is too high, or water leaks from the door, then stops with E04.
|
Overfill / Pressure System Fault | View Details |
| E05 |
Washer does not heat water; the cycle takes unusually long or stops with E05.
|
Heating Circuit Fault | View Details |
| E06 |
Washer drum does not rotate or struggles to turn; E06 is displayed during wash or spin.
|
Motor Drive Fault | View Details |
| E07 |
Washer attempts to spin but stops; it may make clicking sounds and E07 is displayed.
|
Tachometer / Motor Speed Feedback Fault | View Details |
| E08 |
Washer stops mid-cycle with E08; often associated with an unbalanced load or spin issues.
|
Unbalanced Load / Spin Protection Fault | View Details |
| E09 |
Washer stops and displays E09; often with no drum movement at all from the start of the cycle.
|
Inverter / Motor Power Module Fault (for inverter motor models) | View Details |
| E10 |
Washer does not fill within the expected time; E10 is displayed early in the cycle.
|
Water Fill Timeout | View Details |
| E11 |
Washer fills but then quickly drains or cannot maintain the water level; E11 is displayed.
|
Water Level / Pressure Sensor Fault | View Details |
| E12 |
Washer stops with E12; often during the heating phase, sometimes accompanied by lukewarm water.
|
NTC Temperature Sensor Fault | View Details |
| E13 |
Washer displays E13, often associated with water detected in the base tray or leak protection activation.
|
Leak / AquaStop Activation | View Details |
| E14 |
Washer shows E14 and will not start or complete a program, often related to control issues.
|
Main Control Board Communication / Internal Fault | View Details |
| E15 |
Washer displays E15, often with no response from buttons or erratic behavior.
|
User Interface / Display Board Fault | View Details |
| E16 |
Washer door will not unlock at the end of the cycle, E16 is displayed or the lock symbol remains on.
|
Door Unlock Fault | View Details |
| E17 |
Washer stops with E17, often during the spin cycle, sometimes accompanied by high vibration.
|
Excessive Vibration / Out-of-Balance Protection | View Details |
| E18 |
Washer shows E18 and does not drain or spin properly, sometimes intermittent.
|
Drain Pump Electrical Fault | View Details |
| E19 |
Washer displays E19, often related to detergent drawer or water distribution issues.
|
Detergent Drawer / Water Distribution Valve Fault | View Details |
| E20 |
Washer shows E20 and will not start or complete a cycle, often after power issues.
|
Power Supply / Voltage Fault | View Details |
| – |
Washer displays incorrect time remaining or random program behavior without specific error codes
|
Control Logic / Sensor Calibration Issues | View Details |
| – |
Washer does not take in fabric softener from the drawer
|
Softener Siphon / Drawer Flow Fault | View Details |
| – |
Washer door will not open at the end of the cycle, no error code shown
|
Door Stuck / Lock Not Releasing | View Details |
| – |
Washer fills and drains but drum does not turn at all during wash or spin
|
Complete Drum Drive Failure | View Details |
| – |
Washer fills with water even when switched off, slowly over time
|
Inlet Valve Not Closing Properly | View Details |
| – |
Washer has a bad odor inside the drum or from the detergent drawer
|
Biofilm / Mold and Bacteria Build-Up | View Details |
| – |
Washer hums but does not fill with water at the start of the cycle
|
Water Inlet Flow Restriction | View Details |
| – |
Washer is dead, no lights or display, and does not respond to the power button.
|
No Power / Dead Appliance | View Details |
| – |
Washer leaks water from the front door area during wash
|
Door Seal (Gasket) Leak | View Details |
| – |
Washer leaks water from underneath the machine
|
Internal Hose or Pump Leak | View Details |
| – |
Washer leaves clothes soaking wet at the end of the cycle
|
Poor Spin / Residual Water in Laundry | View Details |
| – |
Washer leaves detergent or fabric softener in the drawer at the end of the cycle
|
Poor Detergent Drawer Rinsing | View Details |
| – |
Washer makes loud banging or knocking noises during spin
|
Excessive Vibration / Suspension or Bearing Wear | View Details |
| – |
Washer powers on but will not start any program when Start/Pause is pressed.
|
Start Circuit / Program Inhibit Fault | View Details |
| – |
Washer produces a high-pitched squeal or grinding noise when spinning
|
Drum Bearing or Drive Pulley Fault | View Details |
| – |
Washer takes much longer than the displayed time to complete a cycle
|
Extended Cycle Time / Heating or Balance Issues | View Details |
| – |
Washer trips the household circuit breaker or RCD during operation
|
Electrical Short or Earth Leakage | View Details |
| – |
Washer vibrates excessively and "walks" across the floor during spin on a new installation
|
Installation / Transport Bolt Issue | View Details |
No matching codes found
Advertisements