Levoit
Levoit Cordless Vacuums Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E1
Cordless vacuum will not power on; the display shows E1 shortly after pressing the power button.
Battery Pack Communication Error
E2
Vacuum powers on briefly, then shuts off with E2 on the display.
Overcurrent Protection / Motor Overload
E3
Vacuum stops and displays E3 when using the motorized floor head.
Brushroll Motor Overload / Jam Protection
E4
Vacuum shuts down with E4 after a few minutes of use, especially on high power.
Overtemperature Protection (Main Motor Overheating)
E5
Display shows E5 and the vacuum will not charge when placed on the charging base.
Charging Fault / Charger-Battery Communication Error
E6
Vacuum shows E6 and suction is disabled while lights still work.
Suction Motor Driver Fault
E7
Vacuum displays E7 and the brushroll will not spin, though suction works.
Brushroll Motor Communication / Driver Error
E8
Vacuum shows E8 and shuts off immediately when trigger or power button is pressed.
Battery Undervoltage / Deep Discharge Protection
E9
Vacuum displays E9 and will not start; occurs after recent drop or impact.
Internal Sensor / Accelerometer Fault
F1
Vacuum beeps and shows F1; suction is weak and fluctuating.
Airflow Restriction Detected
F2
Vacuum shows F2 and runs only at low power, ignoring higher power settings.
Power Mode Control / Button Fault
F3
Vacuum displays F3 and the LED headlight on the floor head flickers or does not turn on.
Accessory Power Output Fault
F4
Vacuum shows F4 and shuts off when tilted at certain angles.
Tilt / Orientation Sensor Error
F5
Vacuum displays F5 and cannot detect the dust cup; the unit will not start.
Dust Cup Presence Switch Fault
F6
Vacuum displays F6 and runs for only a few seconds before shutting off.
Battery Temperature Protection
F7
Vacuum displays F7 and cannot connect to the charging dock’s smart features (if applicable).
Dock Communication / Smart Interface Error
Symptom
Attachments (crevice tool, dusting brush) have very weak suction compared to the floor head.
Accessory Airflow Restriction / Leak
Symptom
Battery will not charge; the charger light stays off or blinks rapidly.
Charging Failure
Symptom
Brushroll does not spin, but suction works normally (no error code).
Brushroll Drive Failure
Symptom
Dust escapes from around the dust cup area during use.
Dust Cup Seal Failure
Symptom
LED headlight on floor head does not turn on, but brushroll and suction work.
LED Circuit Failure
Symptom
Motor makes a high-pitched whine and suction pulses up and down.
Cyclone or Air Leak Imbalance
Symptom
Suction is very weak even though the motor sounds normal.
Airflow Restriction / Loss of Seal
Symptom
The trigger or power button sticks or does not respond reliably.
Mechanical Switch Wear / Contamination
Symptom
The vacuum body becomes unusually hot to the touch during normal use.
Thermal Management Problem
Symptom
The vacuum intermittently loses connection to the smart app or Wi-Fi features (if the model supports it).
Wireless Connectivity Issue
Symptom
Vacuum emits a burning smell during use.
Overheating Motor or Brushroll
Symptom
Vacuum is very loud, with grinding or rattling noises from the main body.
Main Motor Bearing Wear / Foreign Object in Fan
Symptom
Vacuum leaves a trail of dust or debris behind the floor head.
Dust Cup or Floor Head Seal Leak
Symptom
Vacuum leaves visible debris on carpets even after multiple passes.
Poor Agitation / Brushroll Inefficiency
Symptom
Vacuum makes loud clicking or knocking noises from the floor head while rolling.
Brushroll Mechanical Interference
Symptom
Vacuum produces a musty or unpleasant odor from the exhaust.
Contaminated Filters / Dust Cup
Symptom
Vacuum runs only in low power mode; high power mode turns off immediately with no code.
High-Load Power Limitation
Symptom
Vacuum turns on but shuts off after a few seconds with no error code.
Intermittent Power / Protection Trip
Symptom
Vacuum vibrates excessively in the hand during use.
Rotational Imbalance
Symptom
Vacuum will not turn on at all; no lights, no beeps.
Complete Power Loss
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E1 |
Cordless vacuum will not power on; the display shows E1 shortly after pressing the power button.
|
Battery Pack Communication Error | View Details |
| E2 |
Vacuum powers on briefly, then shuts off with E2 on the display.
|
Overcurrent Protection / Motor Overload | View Details |
| E3 |
Vacuum stops and displays E3 when using the motorized floor head.
|
Brushroll Motor Overload / Jam Protection | View Details |
| E4 |
Vacuum shuts down with E4 after a few minutes of use, especially on high power.
|
Overtemperature Protection (Main Motor Overheating) | View Details |
| E5 |
Display shows E5 and the vacuum will not charge when placed on the charging base.
|
Charging Fault / Charger-Battery Communication Error | View Details |
| E6 |
Vacuum shows E6 and suction is disabled while lights still work.
|
Suction Motor Driver Fault | View Details |
| E7 |
Vacuum displays E7 and the brushroll will not spin, though suction works.
|
Brushroll Motor Communication / Driver Error | View Details |
| E8 |
Vacuum shows E8 and shuts off immediately when trigger or power button is pressed.
|
Battery Undervoltage / Deep Discharge Protection | View Details |
| E9 |
Vacuum displays E9 and will not start; occurs after recent drop or impact.
|
Internal Sensor / Accelerometer Fault | View Details |
| F1 |
Vacuum beeps and shows F1; suction is weak and fluctuating.
|
Airflow Restriction Detected | View Details |
| F2 |
Vacuum shows F2 and runs only at low power, ignoring higher power settings.
|
Power Mode Control / Button Fault | View Details |
| F3 |
Vacuum displays F3 and the LED headlight on the floor head flickers or does not turn on.
|
Accessory Power Output Fault | View Details |
| F4 |
Vacuum shows F4 and shuts off when tilted at certain angles.
|
Tilt / Orientation Sensor Error | View Details |
| F5 |
Vacuum displays F5 and cannot detect the dust cup; the unit will not start.
|
Dust Cup Presence Switch Fault | View Details |
| F6 |
Vacuum displays F6 and runs for only a few seconds before shutting off.
|
Battery Temperature Protection | View Details |
| F7 |
Vacuum displays F7 and cannot connect to the charging dock’s smart features (if applicable).
|
Dock Communication / Smart Interface Error | View Details |
| – |
Attachments (crevice tool, dusting brush) have very weak suction compared to the floor head.
|
Accessory Airflow Restriction / Leak | View Details |
| – |
Battery will not charge; the charger light stays off or blinks rapidly.
|
Charging Failure | View Details |
| – |
Brushroll does not spin, but suction works normally (no error code).
|
Brushroll Drive Failure | View Details |
| – |
Dust escapes from around the dust cup area during use.
|
Dust Cup Seal Failure | View Details |
| – |
LED headlight on floor head does not turn on, but brushroll and suction work.
|
LED Circuit Failure | View Details |
| – |
Motor makes a high-pitched whine and suction pulses up and down.
|
Cyclone or Air Leak Imbalance | View Details |
| – |
Suction is very weak even though the motor sounds normal.
|
Airflow Restriction / Loss of Seal | View Details |
| – |
The trigger or power button sticks or does not respond reliably.
|
Mechanical Switch Wear / Contamination | View Details |
| – |
The vacuum body becomes unusually hot to the touch during normal use.
|
Thermal Management Problem | View Details |
| – |
The vacuum intermittently loses connection to the smart app or Wi-Fi features (if the model supports it).
|
Wireless Connectivity Issue | View Details |
| – |
Vacuum emits a burning smell during use.
|
Overheating Motor or Brushroll | View Details |
| – |
Vacuum is very loud, with grinding or rattling noises from the main body.
|
Main Motor Bearing Wear / Foreign Object in Fan | View Details |
| – |
Vacuum leaves a trail of dust or debris behind the floor head.
|
Dust Cup or Floor Head Seal Leak | View Details |
| – |
Vacuum leaves visible debris on carpets even after multiple passes.
|
Poor Agitation / Brushroll Inefficiency | View Details |
| – |
Vacuum makes loud clicking or knocking noises from the floor head while rolling.
|
Brushroll Mechanical Interference | View Details |
| – |
Vacuum produces a musty or unpleasant odor from the exhaust.
|
Contaminated Filters / Dust Cup | View Details |
| – |
Vacuum runs only in low power mode; high power mode turns off immediately with no code.
|
High-Load Power Limitation | View Details |
| – |
Vacuum turns on but shuts off after a few seconds with no error code.
|
Intermittent Power / Protection Trip | View Details |
| – |
Vacuum vibrates excessively in the hand during use.
|
Rotational Imbalance | View Details |
| – |
Vacuum will not turn on at all; no lights, no beeps.
|
Complete Power Loss | View Details |
No matching codes found
Advertisements