Siemens Washer-Dryer Combos Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E01
Washer-dryer will not start; door symbol flashes and cycle will not begin
Door Lock / Interlock Failure
E02
Washer-dryer does not fill with water or fills very slowly; program stops early with E02
Water Inlet / Fill Fault
E03
Washer-dryer does not drain; water remains in drum and E03 is displayed
Drain Pump / Drainage Fault
E04
Washer-dryer overfills or shows E04; water may be visible in the door seal area or leaking from the front
Overfill / Overflow Protection Activated
E05
Washer-dryer does not heat water during wash; cycles take unusually long or finish cold
Wash Heating Circuit Fault
E06
Drying function does not start or stops quickly with E06; clothes remain wet after drying cycle
Dryer Heating Circuit Fault
E07
Washer-dryer drum does not rotate during wash or spin; humming noise may be heard
Drive Motor / Motor Control Fault
E08
Washer-dryer fails to reach or maintain spin speed; E08 displayed during spin phase
Unbalanced Load / Spin Control Fault
E09
Drying cycle stops early; no heat, and E09 is displayed.
Dryer Heater Overheat / Safety Cut-Out Triggered
E10
Washer-dryer does not detect water level correctly; it may stop with E10 or show erratic fill/drain behavior.
Pressure Sensor / Water Level Fault
E11
Washer-dryer door will not unlock at the end of the cycle; E11 is displayed.
Door Unlock Fault
E12
Drying performance is poor; E12 is displayed, indicating a condenser or heat exchanger warning.
Condenser / Heat Exchanger Blocked
E13
Water is detected in the base tray; the anti-flood system is activated; E13 is displayed, and the machine will not operate.
Leak / AquaStop Activation
E14
Washer-dryer reports E14, indicating issues with water level detection during drying or wash cycles.
Flow Meter / Water Intake Measurement Fault
E15
Control panel unresponsive or displaying random errors; E15 is sometimes logged as a communication fault.
Control Module / User Interface Communication Error
E16
Door lock error during the drying phase; the machine may stop mid-cycle with E16.
Door Lock Monitoring Fault During Drying
E17
Water intake timeout; the machine stops early in the cycle with E17.
Water Fill Time Exceeded
E18
Drain timeout; the machine stops with water in the drum, and E18 is displayed.
Drain Time Exceeded
E19
Internal valve or diverter fault; E19 displayed, often related to the drying water circuit.
Diverter Valve / Recirculation Valve Fault
E20
General motor error; the drum may not turn or turns erratically; E20 displayed.
Motor / Inverter General Fault
E23
Drain pump triac or control fault; E23 displayed, the pump may run continuously or not at all.
Drain Pump Control Circuit Fault
E24
Communication error between the main control and dryer module; E24 displayed.
Internal Communication Fault
E25
Dryer pump or condensate pump fault; E25 displayed, water may remain in the condenser area.
Condensate Pump Failure
E26
Sensor error related to water level or foam; E26 displayed.
Analog Pressure / Foam Sensor Fault
E29
Voltage supply error; E29 displayed, the machine may not start or may stop unexpectedly.
Mains Voltage Out of Range
Symptom
Washer-dryer display is on but buttons do not respond or program cannot be selected
User Interface / Control Panel Fault
Symptom
Washer-dryer does not start at all; no lights or display
No Power / Dead Appliance
Symptom
Washer-dryer door glass becomes extremely hot during drying
Excessive Front Panel Temperature
Symptom
Washer-dryer drum does not turn during drying, but turns during washing
Drying Mode Drum Drive Fault
Symptom
Washer-dryer emits a burning smell during drying or high-temperature wash
Overheating / Electrical Smell
Symptom
Washer-dryer has a strong musty or moldy odor inside the drum
Biofilm / Mold Build-Up
Symptom
Washer-dryer intermittently trips the household circuit breaker or RCD during operation
Electrical Leakage / Short Circuit
Symptom
Washer-dryer leaks water from the front during wash, especially on high water level programs.
Door Seal (Gasket) Leak
Symptom
Washer-dryer leaks water from the rear or underneath during wash or spin.
Internal Hose or Pump Leak
Symptom
Washer-dryer leaves clothes very wet at the end of the wash cycle (no spin or very slow spin)
Spin Not Achieved
Symptom
Washer-dryer leaves detergent residues or white streaks on clothes after washing
Poor Rinsing / Detergent Dispensing Issue
Symptom
Washer-dryer makes loud banging or knocking noises during spin.
Suspension / Shock Absorber Wear
Symptom
Washer-dryer produces a high-pitched squeal or grinding noise when spinning
Drum Bearing or Drive Pulley Fault
Symptom
Washer-dryer stops mid-cycle without draining or spinning, no error code shown
Program Interruption / Control Hang
Symptom
Washer-dryer takes excessively long to dry clothes; laundry comes out damp
Poor Drying Performance
Symptom
Washer-dryer vibrates excessively and "walks" across the floor during spin
Machine Out of Balance / Installation Issue
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E01 |
Washer-dryer will not start; door symbol flashes and cycle will not begin
|
Door Lock / Interlock Failure | View Details |
| E02 |
Washer-dryer does not fill with water or fills very slowly; program stops early with E02
|
Water Inlet / Fill Fault | View Details |
| E03 |
Washer-dryer does not drain; water remains in drum and E03 is displayed
|
Drain Pump / Drainage Fault | View Details |
| E04 |
Washer-dryer overfills or shows E04; water may be visible in the door seal area or leaking from the front
|
Overfill / Overflow Protection Activated | View Details |
| E05 |
Washer-dryer does not heat water during wash; cycles take unusually long or finish cold
|
Wash Heating Circuit Fault | View Details |
| E06 |
Drying function does not start or stops quickly with E06; clothes remain wet after drying cycle
|
Dryer Heating Circuit Fault | View Details |
| E07 |
Washer-dryer drum does not rotate during wash or spin; humming noise may be heard
|
Drive Motor / Motor Control Fault | View Details |
| E08 |
Washer-dryer fails to reach or maintain spin speed; E08 displayed during spin phase
|
Unbalanced Load / Spin Control Fault | View Details |
| E09 |
Drying cycle stops early; no heat, and E09 is displayed.
|
Dryer Heater Overheat / Safety Cut-Out Triggered | View Details |
| E10 |
Washer-dryer does not detect water level correctly; it may stop with E10 or show erratic fill/drain behavior.
|
Pressure Sensor / Water Level Fault | View Details |
| E11 |
Washer-dryer door will not unlock at the end of the cycle; E11 is displayed.
|
Door Unlock Fault | View Details |
| E12 |
Drying performance is poor; E12 is displayed, indicating a condenser or heat exchanger warning.
|
Condenser / Heat Exchanger Blocked | View Details |
| E13 |
Water is detected in the base tray; the anti-flood system is activated; E13 is displayed, and the machine will not operate.
|
Leak / AquaStop Activation | View Details |
| E14 |
Washer-dryer reports E14, indicating issues with water level detection during drying or wash cycles.
|
Flow Meter / Water Intake Measurement Fault | View Details |
| E15 |
Control panel unresponsive or displaying random errors; E15 is sometimes logged as a communication fault.
|
Control Module / User Interface Communication Error | View Details |
| E16 |
Door lock error during the drying phase; the machine may stop mid-cycle with E16.
|
Door Lock Monitoring Fault During Drying | View Details |
| E17 |
Water intake timeout; the machine stops early in the cycle with E17.
|
Water Fill Time Exceeded | View Details |
| E18 |
Drain timeout; the machine stops with water in the drum, and E18 is displayed.
|
Drain Time Exceeded | View Details |
| E19 |
Internal valve or diverter fault; E19 displayed, often related to the drying water circuit.
|
Diverter Valve / Recirculation Valve Fault | View Details |
| E20 |
General motor error; the drum may not turn or turns erratically; E20 displayed.
|
Motor / Inverter General Fault | View Details |
| E23 |
Drain pump triac or control fault; E23 displayed, the pump may run continuously or not at all.
|
Drain Pump Control Circuit Fault | View Details |
| E24 |
Communication error between the main control and dryer module; E24 displayed.
|
Internal Communication Fault | View Details |
| E25 |
Dryer pump or condensate pump fault; E25 displayed, water may remain in the condenser area.
|
Condensate Pump Failure | View Details |
| E26 |
Sensor error related to water level or foam; E26 displayed.
|
Analog Pressure / Foam Sensor Fault | View Details |
| E29 |
Voltage supply error; E29 displayed, the machine may not start or may stop unexpectedly.
|
Mains Voltage Out of Range | View Details |
| – |
Washer-dryer display is on but buttons do not respond or program cannot be selected
|
User Interface / Control Panel Fault | View Details |
| – |
Washer-dryer does not start at all; no lights or display
|
No Power / Dead Appliance | View Details |
| – |
Washer-dryer door glass becomes extremely hot during drying
|
Excessive Front Panel Temperature | View Details |
| – |
Washer-dryer drum does not turn during drying, but turns during washing
|
Drying Mode Drum Drive Fault | View Details |
| – |
Washer-dryer emits a burning smell during drying or high-temperature wash
|
Overheating / Electrical Smell | View Details |
| – |
Washer-dryer has a strong musty or moldy odor inside the drum
|
Biofilm / Mold Build-Up | View Details |
| – |
Washer-dryer intermittently trips the household circuit breaker or RCD during operation
|
Electrical Leakage / Short Circuit | View Details |
| – |
Washer-dryer leaks water from the front during wash, especially on high water level programs.
|
Door Seal (Gasket) Leak | View Details |
| – |
Washer-dryer leaks water from the rear or underneath during wash or spin.
|
Internal Hose or Pump Leak | View Details |
| – |
Washer-dryer leaves clothes very wet at the end of the wash cycle (no spin or very slow spin)
|
Spin Not Achieved | View Details |
| – |
Washer-dryer leaves detergent residues or white streaks on clothes after washing
|
Poor Rinsing / Detergent Dispensing Issue | View Details |
| – |
Washer-dryer makes loud banging or knocking noises during spin.
|
Suspension / Shock Absorber Wear | View Details |
| – |
Washer-dryer produces a high-pitched squeal or grinding noise when spinning
|
Drum Bearing or Drive Pulley Fault | View Details |
| – |
Washer-dryer stops mid-cycle without draining or spinning, no error code shown
|
Program Interruption / Control Hang | View Details |
| – |
Washer-dryer takes excessively long to dry clothes; laundry comes out damp
|
Poor Drying Performance | View Details |
| – |
Washer-dryer vibrates excessively and "walks" across the floor during spin
|
Machine Out of Balance / Installation Issue | View Details |
No matching codes found
Advertisements