Frigidaire Washing Machines Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E11
The washer will not fill or takes longer than 10 minutes to fill; E11 is displayed on Frigidaire front-load washers.
Fill Timeout / Water Inlet Failure
E13
The washer detects water in the base or an overflow condition; E13 is displayed, and the cycle stops.
Water Leak / Overflow Detected
E21
The washer will not drain or drains very slowly; E21 is displayed, and the cycle stops before the spin.
Drain Timeout / Drain Pump Obstruction
E23
Washer will not drain; E23 displayed; pump does not run even though the tub is full of water.
Drain Pump Relay Failure on Control Board
E24
Washer will not drain; E24 displayed; intermittent or no pump operation.
Drain Pump Circuit Error
E31
Washer does not sense water level correctly; may overfill or not fill enough; E31 displayed.
Pressure Sensor / Water Level Sensor Failure
E35
Washer overfills with water or shows E35; water may reach door glass level.
Water Level Overfill Detected
E41
Washer will not start; E41 displayed; control thinks the door is open even when it is closed.
Door Lock Signal Error (Door Open Detected)
E42
Washer door will not unlock at the end of the cycle; E42 displayed.
Door Lock Stuck Closed
E43
Washer will not start or lock the door; E43 displayed.
Door Lock Control Board Driver Error
E44
Washer reports E44; door lock status signal error; may not start or may stop mid-cycle.
Door Lock Status Feedback Error
E45
Washer shows E45; intermittent door lock issues and cycle interruptions.
Door Lock Communication Error
E51
Washer will not spin or tumble; E51 displayed.
Motor Drive Circuit Failure
E52
Washer drum does not reach proper speed; E52 is displayed; it may start then stop spinning.
Motor Tachometer Signal Error
E53
Washer displays E53; motor drive communication or power error; no spin or tumble.
Motor Control Power/Communication Error
E54
Washer intermittently stops spinning; E54 is displayed.
Motor Overcurrent / Overload Error
E55
Washer displays E55; motor does not run or is weak.
Motor Overheating / Thermal Protection
E56
Washer displays E56; severe motor error; no spin or tumble.
Severe Motor Error / No Speed Feedback
E57
Washer displays E57; high current draw detected in the motor circuit.
Motor Overcurrent / Short Circuit
E58
Washer displays E58; low current draw in the motor circuit; the drum may not move under load.
Motor Underload / No Torque
E59
Washer displays E59; motor speed sensor error; the drum may start then stop.
Tachometer Signal Intermittent
E5A
Washer displays E5A; motor control overheating.
Motor Control Overtemperature
E5B
Washer displays E5B; motor control temperature sensor error.
Motor Control Temperature Sensor Fault
E5C
Washer displays E5C: motor control communication error.
Communication Failure Between Main and Motor Control
E61
Washer does not heat water properly: E61 displayed on models with an internal heater.
Water Heating Timeout
E62
Washer overheats water: E62 displayed; water may be excessively hot.
Water Overheating Error
E66
Washer shows E66: heater relay failure detected.
Heater Relay Fault on Control Board
E67
Washer will not start: E67 displayed; control board power error.
Control Board Voltage Error
E68
Washer displays E68: heating circuit leakage or ground fault detected.
Heater Ground Fault / Leakage
E71
Washer shows E71: water temperature sensor out of range.
NTC Temperature Sensor Fault
E74
Washer displays E74: temperature sensor not positioned correctly.
NTC Sensor Position Error
E75
Washer shows E75: water inlet temperature sensor error (on models with an inlet sensor).
Inlet Temperature Sensor Fault
E91
Washer displays E91: communication error between user interface and main control.
User Interface Communication Failure
E93
Washer displays E93; configuration error detected.
Control Board Configuration Fault
E94
Washer displays E94; program mismatch or corrupted cycle data.
Program Configuration Error
E95
Washer displays E95; communication error between microprocessors on control board.
Internal Control Board Communication Fault
Symptom
Top-load Frigidaire washer agitator does not move, but the motor can be heard running.
Agitator Drive / Coupler Failure
Symptom
Top-load Frigidaire washer will not spin, but it will drain.
Lid Switch / Spin Enable Failure
Symptom
Washer door will not unlock after a power outage or cycle interruption (no code shown).
Door Lock Latched with No Power
Symptom
Washer fills with water but will not agitate or tumble.
Drive Motor / Belt / Agitation Failure
Symptom
Washer has a burning smell during operation.
Overheating Component / Belt Slippage
Symptom
Washer has a strong moldy or musty odor inside the drum.
Biofilm / Mold Build-Up
Symptom
Washer is very noisy during spin; loud rumbling or roaring sound.
Drum Bearing Failure
Symptom
Washer leaks water from the front door area.
Door Boot / Bellows Leak
Symptom
Washer leaks water from underneath the cabinet.
Internal Hose / Pump / Tub Leak
Symptom
Washer leaves detergent residue or white streaks on clothes.
Poor Rinsing / Detergent Dispensing Issue
Symptom
Washer makes loud banging or knocking noises during spin; the machine may move or walk.
Excessive Vibration / Suspension Failure
Symptom
Washer overflows or continues filling even when power is off.
Mechanical Inlet Valve Stuck Open
Symptom
Washer takes excessively long to complete cycles.
Extended Cycle Time / Control Sensing Delays
Symptom
Washer will not power on at all; no lights or display response.
No Power / Dead Control
Symptom
Washer will not spin or leaves clothes very wet at the end of the cycle.
No Spin / Poor Spin Performance
Symptom
Washer will not start cycle; lights are on but the Start button does nothing.
User Interface / Start Circuit Fault
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E11 |
The washer will not fill or takes longer than 10 minutes to fill; E11 is displayed on Frigidaire front-load washers.
|
Fill Timeout / Water Inlet Failure | View Details |
| E13 |
The washer detects water in the base or an overflow condition; E13 is displayed, and the cycle stops.
|
Water Leak / Overflow Detected | View Details |
| E21 |
The washer will not drain or drains very slowly; E21 is displayed, and the cycle stops before the spin.
|
Drain Timeout / Drain Pump Obstruction | View Details |
| E23 |
Washer will not drain; E23 displayed; pump does not run even though the tub is full of water.
|
Drain Pump Relay Failure on Control Board | View Details |
| E24 |
Washer will not drain; E24 displayed; intermittent or no pump operation.
|
Drain Pump Circuit Error | View Details |
| E31 |
Washer does not sense water level correctly; may overfill or not fill enough; E31 displayed.
|
Pressure Sensor / Water Level Sensor Failure | View Details |
| E35 |
Washer overfills with water or shows E35; water may reach door glass level.
|
Water Level Overfill Detected | View Details |
| E41 |
Washer will not start; E41 displayed; control thinks the door is open even when it is closed.
|
Door Lock Signal Error (Door Open Detected) | View Details |
| E42 |
Washer door will not unlock at the end of the cycle; E42 displayed.
|
Door Lock Stuck Closed | View Details |
| E43 |
Washer will not start or lock the door; E43 displayed.
|
Door Lock Control Board Driver Error | View Details |
| E44 |
Washer reports E44; door lock status signal error; may not start or may stop mid-cycle.
|
Door Lock Status Feedback Error | View Details |
| E45 |
Washer shows E45; intermittent door lock issues and cycle interruptions.
|
Door Lock Communication Error | View Details |
| E51 |
Washer will not spin or tumble; E51 displayed.
|
Motor Drive Circuit Failure | View Details |
| E52 |
Washer drum does not reach proper speed; E52 is displayed; it may start then stop spinning.
|
Motor Tachometer Signal Error | View Details |
| E53 |
Washer displays E53; motor drive communication or power error; no spin or tumble.
|
Motor Control Power/Communication Error | View Details |
| E54 |
Washer intermittently stops spinning; E54 is displayed.
|
Motor Overcurrent / Overload Error | View Details |
| E55 |
Washer displays E55; motor does not run or is weak.
|
Motor Overheating / Thermal Protection | View Details |
| E56 |
Washer displays E56; severe motor error; no spin or tumble.
|
Severe Motor Error / No Speed Feedback | View Details |
| E57 |
Washer displays E57; high current draw detected in the motor circuit.
|
Motor Overcurrent / Short Circuit | View Details |
| E58 |
Washer displays E58; low current draw in the motor circuit; the drum may not move under load.
|
Motor Underload / No Torque | View Details |
| E59 |
Washer displays E59; motor speed sensor error; the drum may start then stop.
|
Tachometer Signal Intermittent | View Details |
| E5A |
Washer displays E5A; motor control overheating.
|
Motor Control Overtemperature | View Details |
| E5B |
Washer displays E5B; motor control temperature sensor error.
|
Motor Control Temperature Sensor Fault | View Details |
| E5C |
Washer displays E5C: motor control communication error.
|
Communication Failure Between Main and Motor Control | View Details |
| E61 |
Washer does not heat water properly: E61 displayed on models with an internal heater.
|
Water Heating Timeout | View Details |
| E62 |
Washer overheats water: E62 displayed; water may be excessively hot.
|
Water Overheating Error | View Details |
| E66 |
Washer shows E66: heater relay failure detected.
|
Heater Relay Fault on Control Board | View Details |
| E67 |
Washer will not start: E67 displayed; control board power error.
|
Control Board Voltage Error | View Details |
| E68 |
Washer displays E68: heating circuit leakage or ground fault detected.
|
Heater Ground Fault / Leakage | View Details |
| E71 |
Washer shows E71: water temperature sensor out of range.
|
NTC Temperature Sensor Fault | View Details |
| E74 |
Washer displays E74: temperature sensor not positioned correctly.
|
NTC Sensor Position Error | View Details |
| E75 |
Washer shows E75: water inlet temperature sensor error (on models with an inlet sensor).
|
Inlet Temperature Sensor Fault | View Details |
| E91 |
Washer displays E91: communication error between user interface and main control.
|
User Interface Communication Failure | View Details |
| E93 |
Washer displays E93; configuration error detected.
|
Control Board Configuration Fault | View Details |
| E94 |
Washer displays E94; program mismatch or corrupted cycle data.
|
Program Configuration Error | View Details |
| E95 |
Washer displays E95; communication error between microprocessors on control board.
|
Internal Control Board Communication Fault | View Details |
| – |
Top-load Frigidaire washer agitator does not move, but the motor can be heard running.
|
Agitator Drive / Coupler Failure | View Details |
| – |
Top-load Frigidaire washer will not spin, but it will drain.
|
Lid Switch / Spin Enable Failure | View Details |
| – |
Washer door will not unlock after a power outage or cycle interruption (no code shown).
|
Door Lock Latched with No Power | View Details |
| – |
Washer fills with water but will not agitate or tumble.
|
Drive Motor / Belt / Agitation Failure | View Details |
| – |
Washer has a burning smell during operation.
|
Overheating Component / Belt Slippage | View Details |
| – |
Washer has a strong moldy or musty odor inside the drum.
|
Biofilm / Mold Build-Up | View Details |
| – |
Washer is very noisy during spin; loud rumbling or roaring sound.
|
Drum Bearing Failure | View Details |
| – |
Washer leaks water from the front door area.
|
Door Boot / Bellows Leak | View Details |
| – |
Washer leaks water from underneath the cabinet.
|
Internal Hose / Pump / Tub Leak | View Details |
| – |
Washer leaves detergent residue or white streaks on clothes.
|
Poor Rinsing / Detergent Dispensing Issue | View Details |
| – |
Washer makes loud banging or knocking noises during spin; the machine may move or walk.
|
Excessive Vibration / Suspension Failure | View Details |
| – |
Washer overflows or continues filling even when power is off.
|
Mechanical Inlet Valve Stuck Open | View Details |
| – |
Washer takes excessively long to complete cycles.
|
Extended Cycle Time / Control Sensing Delays | View Details |
| – |
Washer will not power on at all; no lights or display response.
|
No Power / Dead Control | View Details |
| – |
Washer will not spin or leaves clothes very wet at the end of the cycle.
|
No Spin / Poor Spin Performance | View Details |
| – |
Washer will not start cycle; lights are on but the Start button does nothing.
|
User Interface / Start Circuit Fault | View Details |
No matching codes found
Advertisements