Hisense Washing Machines Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E1
The washer will not fill with water; E1 is displayed shortly after the cycle starts.
Water Inlet Timeout / No Fill
E10
Washer shows E10 and stops, often at the beginning of the cycle.
Door Not Closed / Door Switch Error
E11
Washer displays E11; cycle stops unexpectedly, often with water still in the drum.
Communication Error Between Main PCB and Motor/Inverter
E12
Washer shows E12; drum does not rotate correctly during wash or spin.
Motor Overload / Stall Detection
E13
Washer displays E13; often associated with water leakage into the base.
Leakage Detected / Anti-Flood Protection
E2
The washer does not drain water; E2 is displayed, and the drum remains full.
Drain Timeout / No Drain
E21
Washer shows E21; drum speed is abnormal during spin.
Spin Speed Sensor / Unstable Spin Fault
E3
The washer drum does not spin, or the spin is very weak; E3 is displayed.
Motor Drive Fault / No Spin
E30
Washer displays E30 and will not start or stops mid-cycle.
Door Locking System General Fault
E31
Washer shows E31; water temperature reading appears incorrect (very hot or very cold) and the cycle aborts.
NTC Temperature Sensor Fault
E32
Washer displays E32; water level reading is unstable, with frequent filling and draining.
Pressure Sensor Calibration / Range Error
E4
The washer displays E4 and stops during the spin cycle; the drum tries to spin but stops repeatedly.
Unbalanced Load / Out-of-Balance Detection
E40
Washer shows E40 and will not start, often accompanied by beeping.
Door Open Detected at Start
E41
Washer displays E41 during the cycle; the door is reported as open while running.
Door lock signal lost during operation
E5
The washer does not heat water; E5 is displayed during the wash cycle.
Water Heating Fault
E51
Washer shows E51; the motor does not run or runs erratically.
Motor power triac / inverter fault
E6
The washer stops mid-cycle with E6; the water level appears incorrect or erratic.
Water Level Sensor / Pressure Switch Fault
E60
Washer displays E60; heating-related malfunction (no heat or overheating).
General heating system error
E7
The washer door will not lock or unlock; E7 is displayed.
Door Lock / Interlock Fault
E8
The washer shows E8 and will not start, or it stops shortly after starting.
Motor Tachometer / Speed Feedback Fault
E9
Washer displays E9; water level rises too high or overflows into the door gasket.
Overfill / Overflow Protection
E90
Washer shows E90, often after a power outage or surge; the machine is unresponsive or erratic.
Configuration / communication error
F01
Washer displays F01 and will not start a cycle.
Water supply fault / low inlet flow
F02
Washer shows F02; the drum is not rotating properly during the wash.
Motor drive error
F03
Washer displays F03; water is not draining at the end of the cycle.
Drain pump fault
F04
Washer shows F04; water level error at the start or during the wash.
Pressure switch / water level error
F05
Washer displays F05; the heater is not functioning correctly.
Heating circuit error
F06
Washer shows F06; door lock error at the start.
Door lock failure
F07
The washer displays F07, indicating a motor-related fault during the spin cycle.
Motor/Tachometer Error
F08
The washer displays F08, indicating a water level too high or an overflow condition.
Overfill Error
F09
The washer displays F09, indicating an internal software or configuration error.
EEPROM / Configuration Fault
Symptom
The washer emits a burning smell or smoke during operation.
Overheating Electrical or Drive Component
Symptom
The washer leaks water from the front door area during the wash or rinse cycle.
Door Gasket (Boot Seal) Leak
Symptom
The washer leaks water from underneath the cabinet during the wash or spin cycle.
Internal Hose or Pump Leak
Symptom
The washer makes loud banging or knocking noises during the spin cycle.
Excessive Vibration / Suspension Failure
Symptom
The washer produces a high-pitched squealing or grinding noise when spinning.
Drum Bearing or Drive System Wear
Symptom
The washer will not power on; there are no lights or display.
No Power / Dead Appliance
Symptom
Washer causes lights to flicker or trips the circuit breaker when starting.
Electrical Overload / Short Circuit
Symptom
Washer door remains locked after the cycle ends, and no error code is shown.
Door Lock Stuck Closed
Symptom
Washer drum does not turn at all during the wash cycle but can be turned by hand.
Drive System Failure
Symptom
Washer fills and drains repeatedly without progressing into the wash cycle.
Water Level Sensing / Siphoning Issue
Symptom
Washer has a strong musty or moldy odor inside the drum.
Biofilm and Mold Build-Up
Symptom
Washer leaves clothes very wet at the end of the cycle.
Poor Spin Performance
Symptom
Washer leaves visible detergent or powder residue on clothes.
Poor Rinsing / Detergent Dispensing Issue
Symptom
Washer powers on but will not start any cycle when Start/Pause is pressed.
User Interface / Control Lock or Start Circuit Issue
Symptom
Washer takes much longer than the displayed time to complete a cycle.
Extended Cycle Time / Auto Time Adjustment
Symptom
Washer vibrates excessively and 'walks' across the floor, even with small loads.
Installation / Suspension Imbalance
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E1 |
The washer will not fill with water; E1 is displayed shortly after the cycle starts.
|
Water Inlet Timeout / No Fill | View Details |
| E10 |
Washer shows E10 and stops, often at the beginning of the cycle.
|
Door Not Closed / Door Switch Error | View Details |
| E11 |
Washer displays E11; cycle stops unexpectedly, often with water still in the drum.
|
Communication Error Between Main PCB and Motor/Inverter | View Details |
| E12 |
Washer shows E12; drum does not rotate correctly during wash or spin.
|
Motor Overload / Stall Detection | View Details |
| E13 |
Washer displays E13; often associated with water leakage into the base.
|
Leakage Detected / Anti-Flood Protection | View Details |
| E2 |
The washer does not drain water; E2 is displayed, and the drum remains full.
|
Drain Timeout / No Drain | View Details |
| E21 |
Washer shows E21; drum speed is abnormal during spin.
|
Spin Speed Sensor / Unstable Spin Fault | View Details |
| E3 |
The washer drum does not spin, or the spin is very weak; E3 is displayed.
|
Motor Drive Fault / No Spin | View Details |
| E30 |
Washer displays E30 and will not start or stops mid-cycle.
|
Door Locking System General Fault | View Details |
| E31 |
Washer shows E31; water temperature reading appears incorrect (very hot or very cold) and the cycle aborts.
|
NTC Temperature Sensor Fault | View Details |
| E32 |
Washer displays E32; water level reading is unstable, with frequent filling and draining.
|
Pressure Sensor Calibration / Range Error | View Details |
| E4 |
The washer displays E4 and stops during the spin cycle; the drum tries to spin but stops repeatedly.
|
Unbalanced Load / Out-of-Balance Detection | View Details |
| E40 |
Washer shows E40 and will not start, often accompanied by beeping.
|
Door Open Detected at Start | View Details |
| E41 |
Washer displays E41 during the cycle; the door is reported as open while running.
|
Door lock signal lost during operation | View Details |
| E5 |
The washer does not heat water; E5 is displayed during the wash cycle.
|
Water Heating Fault | View Details |
| E51 |
Washer shows E51; the motor does not run or runs erratically.
|
Motor power triac / inverter fault | View Details |
| E6 |
The washer stops mid-cycle with E6; the water level appears incorrect or erratic.
|
Water Level Sensor / Pressure Switch Fault | View Details |
| E60 |
Washer displays E60; heating-related malfunction (no heat or overheating).
|
General heating system error | View Details |
| E7 |
The washer door will not lock or unlock; E7 is displayed.
|
Door Lock / Interlock Fault | View Details |
| E8 |
The washer shows E8 and will not start, or it stops shortly after starting.
|
Motor Tachometer / Speed Feedback Fault | View Details |
| E9 |
Washer displays E9; water level rises too high or overflows into the door gasket.
|
Overfill / Overflow Protection | View Details |
| E90 |
Washer shows E90, often after a power outage or surge; the machine is unresponsive or erratic.
|
Configuration / communication error | View Details |
| F01 |
Washer displays F01 and will not start a cycle.
|
Water supply fault / low inlet flow | View Details |
| F02 |
Washer shows F02; the drum is not rotating properly during the wash.
|
Motor drive error | View Details |
| F03 |
Washer displays F03; water is not draining at the end of the cycle.
|
Drain pump fault | View Details |
| F04 |
Washer shows F04; water level error at the start or during the wash.
|
Pressure switch / water level error | View Details |
| F05 |
Washer displays F05; the heater is not functioning correctly.
|
Heating circuit error | View Details |
| F06 |
Washer shows F06; door lock error at the start.
|
Door lock failure | View Details |
| F07 |
The washer displays F07, indicating a motor-related fault during the spin cycle.
|
Motor/Tachometer Error | View Details |
| F08 |
The washer displays F08, indicating a water level too high or an overflow condition.
|
Overfill Error | View Details |
| F09 |
The washer displays F09, indicating an internal software or configuration error.
|
EEPROM / Configuration Fault | View Details |
| – |
The washer emits a burning smell or smoke during operation.
|
Overheating Electrical or Drive Component | View Details |
| – |
The washer leaks water from the front door area during the wash or rinse cycle.
|
Door Gasket (Boot Seal) Leak | View Details |
| – |
The washer leaks water from underneath the cabinet during the wash or spin cycle.
|
Internal Hose or Pump Leak | View Details |
| – |
The washer makes loud banging or knocking noises during the spin cycle.
|
Excessive Vibration / Suspension Failure | View Details |
| – |
The washer produces a high-pitched squealing or grinding noise when spinning.
|
Drum Bearing or Drive System Wear | View Details |
| – |
The washer will not power on; there are no lights or display.
|
No Power / Dead Appliance | View Details |
| – |
Washer causes lights to flicker or trips the circuit breaker when starting.
|
Electrical Overload / Short Circuit | View Details |
| – |
Washer door remains locked after the cycle ends, and no error code is shown.
|
Door Lock Stuck Closed | View Details |
| – |
Washer drum does not turn at all during the wash cycle but can be turned by hand.
|
Drive System Failure | View Details |
| – |
Washer fills and drains repeatedly without progressing into the wash cycle.
|
Water Level Sensing / Siphoning Issue | View Details |
| – |
Washer has a strong musty or moldy odor inside the drum.
|
Biofilm and Mold Build-Up | View Details |
| – |
Washer leaves clothes very wet at the end of the cycle.
|
Poor Spin Performance | View Details |
| – |
Washer leaves visible detergent or powder residue on clothes.
|
Poor Rinsing / Detergent Dispensing Issue | View Details |
| – |
Washer powers on but will not start any cycle when Start/Pause is pressed.
|
User Interface / Control Lock or Start Circuit Issue | View Details |
| – |
Washer takes much longer than the displayed time to complete a cycle.
|
Extended Cycle Time / Auto Time Adjustment | View Details |
| – |
Washer vibrates excessively and 'walks' across the floor, even with small loads.
|
Installation / Suspension Imbalance | View Details |
No matching codes found
Advertisements