Jimmy
Jimmy Cordless Vacuums Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E1
Vacuum will not power on; the battery indicator flashes red rapidly a few times, then turns off.
Battery Pack Protection Trip / Low Voltage Lockout
E2
Vacuum stops after a few seconds of use; a red error light or E2 code appears on the display, and the motor does not restart until cooled.
Motor Overcurrent / Blocked Airflow Protection
E3
Brush head stops spinning, display shows E3 or a brush icon with an error, suction continues.
Motorized Floorhead Overload / Brushroll Jam
E4
Vacuum shuts down with E4 on the display or a continuous red LED, body feels hot to the touch.
Main Motor Overheating Protection
E5
Battery icon flashes, E5 displayed, vacuum stops charging before full, runtime is very short.
Battery Temperature / Charging Protection Fault
E6
Vacuum powers on but immediately shuts off with E6 or beeping, with no motor sound.
Main Control PCB Fault / Internal Communication Error
E7
Display shows E7, suction is weak or pulsing, and motor speed fluctuates.
Cyclone / Airflow Sensor Fault
E8
LED display shows E8, vacuum cannot switch between power modes, and buttons are unresponsive.
Keypad / Mode Switch Circuit Fault
E9
Vacuum shows E9 and will not start, especially after a drop or impact.
Impact / Tilt Sensor Fault
F1
Display shows F1, vacuum runs only at low power, and turbo mode is unavailable.
Power Mode Drive Fault / Current Limit
F2
F2 code on display, vacuum runs but LED lights on the floorhead flicker or do not work.
Accessory Power Output Fault
F3
F3 displayed, vacuum shuts off when a certain attachment is connected.
Accessory Identification / Overload Fault
F4
F4 code, vacuum runs but the battery indicator behaves erratically (jumps from full to empty).
Battery Communication / Fuel Gauge Fault
F5
F5 displayed, vacuum cannot be charged, and the charger LED blinks an error pattern.
Charging Circuit Fault
F6
F6 code, vacuum runs but makes a high-pitched whine, and suction is lower than normal.
Partial Blockage / Cyclone Imbalance Fault
F7
F7 displayed, vacuum vibrates strongly and is noisy, especially at high power.
Motor Imbalance / Fan Damage Fault
F8
F8 code, vacuum stops when tilted at certain angles, and works only when held upright.
Tilt / Orientation Sensor Calibration Fault
F9
F9 displayed, vacuum randomly shuts off even with a full battery, and restarts after trigger release.
Trigger Switch / Power Latch Fault
Symptom
Dust cup does not stay attached or falls off during use.
Dust Cup Latch / Seal Failure
Symptom
Dust leaks from around the dust cup or joints during use.
Air / Dust Leakage
Symptom
LED lights on the motorized floorhead do not turn on, but the brush spins normally.
Floorhead LED Failure
Symptom
Motorized floorhead brush does not spin, but suction is normal and no error code.
Brushroll Drive Failure
Symptom
The extension tube connection feels loose or wobbly, affecting maneuverability.
Mechanical Joint Wear
Symptom
The handheld body becomes very hot to the touch near the motor area.
Excessive Motor Heating
Symptom
The handheld unit or battery shows signs of swelling, cracks, or leakage.
Battery Physical Damage / Safety Hazard
Symptom
The trigger or power button is stuck or does not return smoothly.
Trigger Mechanism Jam
Symptom
The vacuum cannot stand properly on its wall mount or falls off the dock.
Docking / Mounting Issue
Symptom
The vacuum does not respond to mode changes; it is stuck in one power level without any error code.
Mode Control / Button Failure
Symptom
The vacuum runs, but there is a noticeable spark or flicker visible through the vents.
Electrical Arcing in Motor or Connections
Symptom
Vacuum emits a burning smell during or after use.
Overheating / Electrical or Mechanical Burn
Symptom
Vacuum has very weak suction, but the motor sounds normal, and no error code is displayed.
Airflow Restriction / Filter Clogging
Symptom
Vacuum leaves lines of debris on carpet, not picking up well even though suction seems strong.
Poor Pickup / Brushroll or Floorhead Issue
Symptom
Vacuum makes a loud rattling or grinding noise during operation.
Mechanical Noise / Bearing or Debris Issue
Symptom
Vacuum produces an unusual high-pitched whistle during use.
Air Leak / Small Obstruction
Symptom
Vacuum runs for only a few minutes on a full charge, with no error code displayed.
Battery Capacity Degradation
Symptom
Vacuum shuts off intermittently during use, then restarts after a few seconds.
Intermittent Power Loss / Loose Connection
Symptom
Vacuum smells musty or dusty when running.
Odor from Filters / Dust Accumulation
Symptom
Vacuum vibrates excessively in the hand during use.
Vibration / Imbalance
Symptom
Vacuum will not start at all, with no lights and no response when the trigger is pressed.
No Power / Dead Unit
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E1 |
Vacuum will not power on; the battery indicator flashes red rapidly a few times, then turns off.
|
Battery Pack Protection Trip / Low Voltage Lockout | View Details |
| E2 |
Vacuum stops after a few seconds of use; a red error light or E2 code appears on the display, and the motor does not restart until cooled.
|
Motor Overcurrent / Blocked Airflow Protection | View Details |
| E3 |
Brush head stops spinning, display shows E3 or a brush icon with an error, suction continues.
|
Motorized Floorhead Overload / Brushroll Jam | View Details |
| E4 |
Vacuum shuts down with E4 on the display or a continuous red LED, body feels hot to the touch.
|
Main Motor Overheating Protection | View Details |
| E5 |
Battery icon flashes, E5 displayed, vacuum stops charging before full, runtime is very short.
|
Battery Temperature / Charging Protection Fault | View Details |
| E6 |
Vacuum powers on but immediately shuts off with E6 or beeping, with no motor sound.
|
Main Control PCB Fault / Internal Communication Error | View Details |
| E7 |
Display shows E7, suction is weak or pulsing, and motor speed fluctuates.
|
Cyclone / Airflow Sensor Fault | View Details |
| E8 |
LED display shows E8, vacuum cannot switch between power modes, and buttons are unresponsive.
|
Keypad / Mode Switch Circuit Fault | View Details |
| E9 |
Vacuum shows E9 and will not start, especially after a drop or impact.
|
Impact / Tilt Sensor Fault | View Details |
| F1 |
Display shows F1, vacuum runs only at low power, and turbo mode is unavailable.
|
Power Mode Drive Fault / Current Limit | View Details |
| F2 |
F2 code on display, vacuum runs but LED lights on the floorhead flicker or do not work.
|
Accessory Power Output Fault | View Details |
| F3 |
F3 displayed, vacuum shuts off when a certain attachment is connected.
|
Accessory Identification / Overload Fault | View Details |
| F4 |
F4 code, vacuum runs but the battery indicator behaves erratically (jumps from full to empty).
|
Battery Communication / Fuel Gauge Fault | View Details |
| F5 |
F5 displayed, vacuum cannot be charged, and the charger LED blinks an error pattern.
|
Charging Circuit Fault | View Details |
| F6 |
F6 code, vacuum runs but makes a high-pitched whine, and suction is lower than normal.
|
Partial Blockage / Cyclone Imbalance Fault | View Details |
| F7 |
F7 displayed, vacuum vibrates strongly and is noisy, especially at high power.
|
Motor Imbalance / Fan Damage Fault | View Details |
| F8 |
F8 code, vacuum stops when tilted at certain angles, and works only when held upright.
|
Tilt / Orientation Sensor Calibration Fault | View Details |
| F9 |
F9 displayed, vacuum randomly shuts off even with a full battery, and restarts after trigger release.
|
Trigger Switch / Power Latch Fault | View Details |
| – |
Dust cup does not stay attached or falls off during use.
|
Dust Cup Latch / Seal Failure | View Details |
| – |
Dust leaks from around the dust cup or joints during use.
|
Air / Dust Leakage | View Details |
| – |
LED lights on the motorized floorhead do not turn on, but the brush spins normally.
|
Floorhead LED Failure | View Details |
| – |
Motorized floorhead brush does not spin, but suction is normal and no error code.
|
Brushroll Drive Failure | View Details |
| – |
The extension tube connection feels loose or wobbly, affecting maneuverability.
|
Mechanical Joint Wear | View Details |
| – |
The handheld body becomes very hot to the touch near the motor area.
|
Excessive Motor Heating | View Details |
| – |
The handheld unit or battery shows signs of swelling, cracks, or leakage.
|
Battery Physical Damage / Safety Hazard | View Details |
| – |
The trigger or power button is stuck or does not return smoothly.
|
Trigger Mechanism Jam | View Details |
| – |
The vacuum cannot stand properly on its wall mount or falls off the dock.
|
Docking / Mounting Issue | View Details |
| – |
The vacuum does not respond to mode changes; it is stuck in one power level without any error code.
|
Mode Control / Button Failure | View Details |
| – |
The vacuum runs, but there is a noticeable spark or flicker visible through the vents.
|
Electrical Arcing in Motor or Connections | View Details |
| – |
Vacuum emits a burning smell during or after use.
|
Overheating / Electrical or Mechanical Burn | View Details |
| – |
Vacuum has very weak suction, but the motor sounds normal, and no error code is displayed.
|
Airflow Restriction / Filter Clogging | View Details |
| – |
Vacuum leaves lines of debris on carpet, not picking up well even though suction seems strong.
|
Poor Pickup / Brushroll or Floorhead Issue | View Details |
| – |
Vacuum makes a loud rattling or grinding noise during operation.
|
Mechanical Noise / Bearing or Debris Issue | View Details |
| – |
Vacuum produces an unusual high-pitched whistle during use.
|
Air Leak / Small Obstruction | View Details |
| – |
Vacuum runs for only a few minutes on a full charge, with no error code displayed.
|
Battery Capacity Degradation | View Details |
| – |
Vacuum shuts off intermittently during use, then restarts after a few seconds.
|
Intermittent Power Loss / Loose Connection | View Details |
| – |
Vacuum smells musty or dusty when running.
|
Odor from Filters / Dust Accumulation | View Details |
| – |
Vacuum vibrates excessively in the hand during use.
|
Vibration / Imbalance | View Details |
| – |
Vacuum will not start at all, with no lights and no response when the trigger is pressed.
|
No Power / Dead Unit | View Details |
No matching codes found
Advertisements