Hoover Dishwashers Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E01
Dishwasher will not start; the display shows E01, and the cycle will not begin.
Door Lock / Door Switch Fault
E02
The dishwasher stops shortly after starting; E02 is displayed, and no water is heard entering the tub.
Water Inlet / Fill Fault
E03
The dishwasher stops mid-cycle with water left in the bottom; E03 is displayed.
Drain Pump / Drainage Fault
E04
The cycle stops with E04; the dishwasher appears to overfill, or the water level is too high in the tub.
Overfill / Pressure Switch Fault
E05
The dishwasher stops with E05; water fills but does not heat, and dishes come out cold and wet.
Heating Circuit Fault
E06
The dishwasher displays E06 and stops; spray arms may not be rotating, and wash performance is poor.
Circulation Pump / Wash Pump Fault
E07
The dishwasher shows E07; water may leak into the base, and the machine stops with the drain pump running continuously.
Anti-Flood / Leak Detection Activated
E08
The dishwasher displays E08; the water level appears low, and spray arms may not reach all dishes.
Insufficient Water Level / Fill Level Error
E09
The dishwasher shows E09; the machine may stop during a wash with no obvious mechanical noise change.
Control Board / EEPROM Fault
E10
The dishwasher displays E10; drying performance is poor, and sometimes the fan does not run.
Drying System / Fan Fault
E11
Dishwasher displays E11; water may be too hot or too cold, and cycles may end prematurely.
NTC Temperature Sensor Fault
E12
Dishwasher displays E12; water appears excessively hot, with steam escaping when the door is opened.
Overheating / Thermostat Control Fault
E13
Dishwasher displays E13; water may be entering too slowly or intermittently, sometimes accompanied by unusual fill noises.
Flow Meter / Water Distribution Fault
E14
Dishwasher displays E14; the machine may stop during wash with no clear mechanical symptom.
Communication Error Between Control and Sensors
E15
Dishwasher displays E15; the machine may not start and may beep repeatedly.
Water Intake Timeout / No Fill
E16
Dishwasher displays E16; water may continuously enter the machine even when off, or overfilling occurs.
Inlet Valve Stuck Open
E17
Dishwasher displays E17; often associated with very high or very low mains voltage conditions.
Mains Supply Voltage Error
E18
Dishwasher displays E18; often near the end of the cycle, with poor drying and sometimes standing water.
Final Drain / End-of-Cycle Drain Fault
Symptom
Detergent tablet remains in the dispenser at the end of the cycle.
Detergent Dispenser Not Opening / Spray Coverage Issue
Symptom
Dishes are not coming out clean; food residues remain on plates and glasses.
Poor Wash Performance
Symptom
Dishes remain wet at the end of the cycle; poor drying performance.
Poor Drying / Condensation Issue
Symptom
Dishwasher does not fill with water; you hear a humming or clicking, but no water enters.
No Water Filling
Symptom
Dishwasher does not power on at all; no lights or display, completely dead.
No Power / Mains Input Fault
Symptom
Dishwasher door drops down quickly or will not stay open at a mid-position.
Door Hinge / Spring / Cable Failure
Symptom
Dishwasher door will not latch closed; cycle cannot be started.
Door Latch / Catch Misalignment
Symptom
Dishwasher fills and washes but does not drain; water remains in the bottom at the end of the cycle.
No Drain / Standing Water
Symptom
Dishwasher fills with water but does not start washing; spray arms do not move, and there is no wash noise.
Circulation Pump Not Operating
Symptom
Dishwasher interior light (if fitted) does not work, but machine otherwise operates normally.
Interior Light Failure
Symptom
Dishwasher leaks water from the front bottom of the door during the wash cycle.
Door Seal / Lower Door Leak
Symptom
Dishwasher leaks water from underneath; water appears on the floor under the machine.
Base Leak / Hose or Sump Leak
Symptom
Dishwasher makes a high-pitched squealing or whining noise during operation.
Pump Bearing Wear / Motor Noise
Symptom
Dishwasher makes loud grinding or rattling noises during the wash cycle.
Foreign Object in Pump or Spray Arm Interference
Symptom
Dishwasher powers on but will not start any program; the start button is unresponsive.
User Interface / Start Circuit Fault
Symptom
Dishwasher runs for an unusually long time or never seems to finish the cycle.
Extended Cycle Time / Heating or Sensor Issue
Symptom
Dishwasher trips the household circuit breaker or RCD during operation.
Electrical Short / Earth Leakage
Symptom
Dishwasher vibrates excessively or moves during operation, especially during drain or wash phases.
Excessive Vibration / Installation Fault
Symptom
Glasses appear cloudy or have a white film after washing.
Limescale / Rinse Quality Issue
Symptom
Unpleasant smell coming from the dishwasher, even when not in use.
Odour / Biofilm Build-Up
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E01 |
Dishwasher will not start; the display shows E01, and the cycle will not begin.
|
Door Lock / Door Switch Fault | View Details |
| E02 |
The dishwasher stops shortly after starting; E02 is displayed, and no water is heard entering the tub.
|
Water Inlet / Fill Fault | View Details |
| E03 |
The dishwasher stops mid-cycle with water left in the bottom; E03 is displayed.
|
Drain Pump / Drainage Fault | View Details |
| E04 |
The cycle stops with E04; the dishwasher appears to overfill, or the water level is too high in the tub.
|
Overfill / Pressure Switch Fault | View Details |
| E05 |
The dishwasher stops with E05; water fills but does not heat, and dishes come out cold and wet.
|
Heating Circuit Fault | View Details |
| E06 |
The dishwasher displays E06 and stops; spray arms may not be rotating, and wash performance is poor.
|
Circulation Pump / Wash Pump Fault | View Details |
| E07 |
The dishwasher shows E07; water may leak into the base, and the machine stops with the drain pump running continuously.
|
Anti-Flood / Leak Detection Activated | View Details |
| E08 |
The dishwasher displays E08; the water level appears low, and spray arms may not reach all dishes.
|
Insufficient Water Level / Fill Level Error | View Details |
| E09 |
The dishwasher shows E09; the machine may stop during a wash with no obvious mechanical noise change.
|
Control Board / EEPROM Fault | View Details |
| E10 |
The dishwasher displays E10; drying performance is poor, and sometimes the fan does not run.
|
Drying System / Fan Fault | View Details |
| E11 |
Dishwasher displays E11; water may be too hot or too cold, and cycles may end prematurely.
|
NTC Temperature Sensor Fault | View Details |
| E12 |
Dishwasher displays E12; water appears excessively hot, with steam escaping when the door is opened.
|
Overheating / Thermostat Control Fault | View Details |
| E13 |
Dishwasher displays E13; water may be entering too slowly or intermittently, sometimes accompanied by unusual fill noises.
|
Flow Meter / Water Distribution Fault | View Details |
| E14 |
Dishwasher displays E14; the machine may stop during wash with no clear mechanical symptom.
|
Communication Error Between Control and Sensors | View Details |
| E15 |
Dishwasher displays E15; the machine may not start and may beep repeatedly.
|
Water Intake Timeout / No Fill | View Details |
| E16 |
Dishwasher displays E16; water may continuously enter the machine even when off, or overfilling occurs.
|
Inlet Valve Stuck Open | View Details |
| E17 |
Dishwasher displays E17; often associated with very high or very low mains voltage conditions.
|
Mains Supply Voltage Error | View Details |
| E18 |
Dishwasher displays E18; often near the end of the cycle, with poor drying and sometimes standing water.
|
Final Drain / End-of-Cycle Drain Fault | View Details |
| – |
Detergent tablet remains in the dispenser at the end of the cycle.
|
Detergent Dispenser Not Opening / Spray Coverage Issue | View Details |
| – |
Dishes are not coming out clean; food residues remain on plates and glasses.
|
Poor Wash Performance | View Details |
| – |
Dishes remain wet at the end of the cycle; poor drying performance.
|
Poor Drying / Condensation Issue | View Details |
| – |
Dishwasher does not fill with water; you hear a humming or clicking, but no water enters.
|
No Water Filling | View Details |
| – |
Dishwasher does not power on at all; no lights or display, completely dead.
|
No Power / Mains Input Fault | View Details |
| – |
Dishwasher door drops down quickly or will not stay open at a mid-position.
|
Door Hinge / Spring / Cable Failure | View Details |
| – |
Dishwasher door will not latch closed; cycle cannot be started.
|
Door Latch / Catch Misalignment | View Details |
| – |
Dishwasher fills and washes but does not drain; water remains in the bottom at the end of the cycle.
|
No Drain / Standing Water | View Details |
| – |
Dishwasher fills with water but does not start washing; spray arms do not move, and there is no wash noise.
|
Circulation Pump Not Operating | View Details |
| – |
Dishwasher interior light (if fitted) does not work, but machine otherwise operates normally.
|
Interior Light Failure | View Details |
| – |
Dishwasher leaks water from the front bottom of the door during the wash cycle.
|
Door Seal / Lower Door Leak | View Details |
| – |
Dishwasher leaks water from underneath; water appears on the floor under the machine.
|
Base Leak / Hose or Sump Leak | View Details |
| – |
Dishwasher makes a high-pitched squealing or whining noise during operation.
|
Pump Bearing Wear / Motor Noise | View Details |
| – |
Dishwasher makes loud grinding or rattling noises during the wash cycle.
|
Foreign Object in Pump or Spray Arm Interference | View Details |
| – |
Dishwasher powers on but will not start any program; the start button is unresponsive.
|
User Interface / Start Circuit Fault | View Details |
| – |
Dishwasher runs for an unusually long time or never seems to finish the cycle.
|
Extended Cycle Time / Heating or Sensor Issue | View Details |
| – |
Dishwasher trips the household circuit breaker or RCD during operation.
|
Electrical Short / Earth Leakage | View Details |
| – |
Dishwasher vibrates excessively or moves during operation, especially during drain or wash phases.
|
Excessive Vibration / Installation Fault | View Details |
| – |
Glasses appear cloudy or have a white film after washing.
|
Limescale / Rinse Quality Issue | View Details |
| – |
Unpleasant smell coming from the dishwasher, even when not in use.
|
Odour / Biofilm Build-Up | View Details |
No matching codes found
Advertisements