Rosières Dishwashers Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E1
Cycle will not start; display shows E1 shortly after pressing Start.
Water Inlet Timeout / No Fill
E10
E10 displayed; salt or rinse aid indicators may behave erratically.
Water Softener / Regeneration System Error
E11
E11 appears; dishwasher may not start or may stop shortly after filling.
Door Lock / Door Switch Error
E12
E12 displayed; often associated with poor drying and fan noise issues on models with Turbo Dry.
Drying Fan / Condenser System Fault
E13
E13 appears; dishwasher may stop during fill or rinse phases.
Flow Meter / Water Intake Measurement Error
E14
E14 displayed; the machine may not start or may reset repeatedly.
Control Panel / User Interface Communication Error
E15
E15 appears; dishwasher may not start, and the drain pump may run continuously.
Permanent Leak / Base Flood Condition
E16
E16 displayed; dishwasher may not fill correctly or may overfill.
Inlet Valve Stuck Open / Overfill Detection
E17
E17 appears; dishwasher may stop during draining or at program end.
Drain Sensor / Water Presence Detection Error
E18
E18 displayed; dishwasher may not start and may beep repeatedly.
Configuration / EEPROM Error
E19
E19 appears intermittently; the dishwasher may pause or restart mid-cycle.
Low Voltage / Power Supply Error
E2
Dishwasher stops mid-cycle and displays E2; water remains in the tub.
Drain Timeout / Drain Pump Fault
E20
E20 displayed; the dishwasher may not respond to buttons or may freeze mid-cycle.
General Communication / Internal Error
E3
Cycle runs but dishes are cold and still dirty; E3 appears near the end of the program.
Heating Circuit Failure
E4
Dishwasher stops and shows E4; water may be heard draining continuously, even when off.
Anti-Flood / Overflow Protection Activated
E5
Program ends quickly with E5; dishes are not washed properly, and the water level seems low.
Water Level / Pressure Switch Error
E6
Dishwasher stops with E6; it may not start the washing phase after filling.
Turbidity / Water Quality Sensor or Flow Sensor Error
E7
Display shows E7; the dishwasher may not heat or may stop unexpectedly.
NTC Temperature Sensor Fault
E8
E8 displayed; poor washing performance and unusual water levels.
Circulation Pump / Motor Fault
E9
E9 appears; dishwasher may stop shortly after starting or during the heating phase.
Heater Relay / Control Board Heating Control Error
Symptom
Condensation or steam escaping from the top of the door, causing a damp worktop.
Door Seal / Venting Issue
Symptom
Cycle times are much longer than normal; the dishwasher seems to run endlessly
Extended Cycle Duration
Symptom
Detergent tablet remains in the dispenser at the end of the cycle
Detergent Dispenser Not Opening Correctly
Symptom
Dishes come out dirty or with food residue after a full cycle.
Poor Wash Performance
Symptom
Dishwasher door drops down quickly or will not stay open at a mid-position
Door Spring / Hinge Cable Failure
Symptom
Dishwasher makes loud grinding or rattling noises during the wash cycle
Mechanical Noise from Pump or Foreign Object
Symptom
Dishwasher stops mid-cycle without draining, and no error code is shown
Intermittent Power or Control Fault
Symptom
Dishwasher vibrates excessively or moves during operation
Excessive Vibration / Installation Fault
Symptom
Glasses and dishes are cloudy or have a white film after washing.
Limescale / Poor Rinsing
Symptom
High-pitched squealing or whining noise during draining
Drain Pump Bearing or Impeller Noise
Symptom
Rinse aid is not dispensing; dishes are left with water spots
Rinse Aid Dispenser Failure
Symptom
Rust spots appearing on cutlery or inside the tub.
Corrosion / Material Attack
Symptom
Strong, unpleasant smell when opening the dishwasher, even when empty
Biofilm / Bacterial Odor Buildup
Symptom
The dishwasher does not drain at the end of the cycle; water remains in the bottom.
Poor Drainage Without Error Code
Symptom
The dishwasher fills with water but does not wash; the spray arms do not move.
Circulation Failure Without Error Code
Symptom
The dishwasher leaks from underneath or at the sides of the cabinet.
Base Leak / Internal Hose or Sump Leak
Symptom
The dishwasher leaks water from the door area during a wash cycle.
Door Seal / Spray Pattern Leak
Symptom
The dishwasher powers on but will not start a cycle; the Start button is unresponsive or beeps.
Start Inhibit / Door or UI Logic Fault
Symptom
The dishwasher will not power on at all; no lights or display.
No Mains Power / Power Entry Fault
Symptom
Top rack dishes are not getting clean, while the bottom rack is washed properly
Upper Spray Arm or Feed Tube Blockage
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E1 |
Cycle will not start; display shows E1 shortly after pressing Start.
|
Water Inlet Timeout / No Fill | View Details |
| E10 |
E10 displayed; salt or rinse aid indicators may behave erratically.
|
Water Softener / Regeneration System Error | View Details |
| E11 |
E11 appears; dishwasher may not start or may stop shortly after filling.
|
Door Lock / Door Switch Error | View Details |
| E12 |
E12 displayed; often associated with poor drying and fan noise issues on models with Turbo Dry.
|
Drying Fan / Condenser System Fault | View Details |
| E13 |
E13 appears; dishwasher may stop during fill or rinse phases.
|
Flow Meter / Water Intake Measurement Error | View Details |
| E14 |
E14 displayed; the machine may not start or may reset repeatedly.
|
Control Panel / User Interface Communication Error | View Details |
| E15 |
E15 appears; dishwasher may not start, and the drain pump may run continuously.
|
Permanent Leak / Base Flood Condition | View Details |
| E16 |
E16 displayed; dishwasher may not fill correctly or may overfill.
|
Inlet Valve Stuck Open / Overfill Detection | View Details |
| E17 |
E17 appears; dishwasher may stop during draining or at program end.
|
Drain Sensor / Water Presence Detection Error | View Details |
| E18 |
E18 displayed; dishwasher may not start and may beep repeatedly.
|
Configuration / EEPROM Error | View Details |
| E19 |
E19 appears intermittently; the dishwasher may pause or restart mid-cycle.
|
Low Voltage / Power Supply Error | View Details |
| E2 |
Dishwasher stops mid-cycle and displays E2; water remains in the tub.
|
Drain Timeout / Drain Pump Fault | View Details |
| E20 |
E20 displayed; the dishwasher may not respond to buttons or may freeze mid-cycle.
|
General Communication / Internal Error | View Details |
| E3 |
Cycle runs but dishes are cold and still dirty; E3 appears near the end of the program.
|
Heating Circuit Failure | View Details |
| E4 |
Dishwasher stops and shows E4; water may be heard draining continuously, even when off.
|
Anti-Flood / Overflow Protection Activated | View Details |
| E5 |
Program ends quickly with E5; dishes are not washed properly, and the water level seems low.
|
Water Level / Pressure Switch Error | View Details |
| E6 |
Dishwasher stops with E6; it may not start the washing phase after filling.
|
Turbidity / Water Quality Sensor or Flow Sensor Error | View Details |
| E7 |
Display shows E7; the dishwasher may not heat or may stop unexpectedly.
|
NTC Temperature Sensor Fault | View Details |
| E8 |
E8 displayed; poor washing performance and unusual water levels.
|
Circulation Pump / Motor Fault | View Details |
| E9 |
E9 appears; dishwasher may stop shortly after starting or during the heating phase.
|
Heater Relay / Control Board Heating Control Error | View Details |
| – |
Condensation or steam escaping from the top of the door, causing a damp worktop.
|
Door Seal / Venting Issue | View Details |
| – |
Cycle times are much longer than normal; the dishwasher seems to run endlessly
|
Extended Cycle Duration | View Details |
| – |
Detergent tablet remains in the dispenser at the end of the cycle
|
Detergent Dispenser Not Opening Correctly | View Details |
| – |
Dishes come out dirty or with food residue after a full cycle.
|
Poor Wash Performance | View Details |
| – |
Dishwasher door drops down quickly or will not stay open at a mid-position
|
Door Spring / Hinge Cable Failure | View Details |
| – |
Dishwasher makes loud grinding or rattling noises during the wash cycle
|
Mechanical Noise from Pump or Foreign Object | View Details |
| – |
Dishwasher stops mid-cycle without draining, and no error code is shown
|
Intermittent Power or Control Fault | View Details |
| – |
Dishwasher vibrates excessively or moves during operation
|
Excessive Vibration / Installation Fault | View Details |
| – |
Glasses and dishes are cloudy or have a white film after washing.
|
Limescale / Poor Rinsing | View Details |
| – |
High-pitched squealing or whining noise during draining
|
Drain Pump Bearing or Impeller Noise | View Details |
| – |
Rinse aid is not dispensing; dishes are left with water spots
|
Rinse Aid Dispenser Failure | View Details |
| – |
Rust spots appearing on cutlery or inside the tub.
|
Corrosion / Material Attack | View Details |
| – |
Strong, unpleasant smell when opening the dishwasher, even when empty
|
Biofilm / Bacterial Odor Buildup | View Details |
| – |
The dishwasher does not drain at the end of the cycle; water remains in the bottom.
|
Poor Drainage Without Error Code | View Details |
| – |
The dishwasher fills with water but does not wash; the spray arms do not move.
|
Circulation Failure Without Error Code | View Details |
| – |
The dishwasher leaks from underneath or at the sides of the cabinet.
|
Base Leak / Internal Hose or Sump Leak | View Details |
| – |
The dishwasher leaks water from the door area during a wash cycle.
|
Door Seal / Spray Pattern Leak | View Details |
| – |
The dishwasher powers on but will not start a cycle; the Start button is unresponsive or beeps.
|
Start Inhibit / Door or UI Logic Fault | View Details |
| – |
The dishwasher will not power on at all; no lights or display.
|
No Mains Power / Power Entry Fault | View Details |
| – |
Top rack dishes are not getting clean, while the bottom rack is washed properly
|
Upper Spray Arm or Feed Tube Blockage | View Details |
No matching codes found
Advertisements