SMEG Ranges & Cooktops Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E0
The cooktop or range display shows E0, and burners will not operate.
Touch Control Panel Communication Fault
E1
The induction cooktop or electronic range shows E1 and disables one or more zones.
Cookware Detection / Induction Coil Fault
E2
An induction zone stops heating, and E2 appears on the display.
Induction Zone Overheating Protection
E3
The induction cooktop shows E3 and shuts down when high power is selected.
Supply Voltage Out of Range / Overvoltage
E4
Induction zone displays E4 and will not heat.
Induction Power Module Fault / IGBT Failure
E5
Induction cooktop shows E5 and beeps; zones shut down.
Cooktop Overtemperature / Glass Surface Overheat
E6
Induction cooktop displays E6 and will not start any zones.
Internal Communication Error Between User Interface and Power Module
E7
Induction zone shows E7 and does not heat properly.
Induction Coil Temperature Sensor Fault
E8
Induction cooktop intermittently shows E8, and zones cut out under load.
Internal Power Supply / Low Voltage on Control Electronics
E9
Induction cooktop shows E9, and all zones are disabled.
Configuration / Calibration Error
Er01
Gas cooktop with electronic ignition shows Er01, and the burners will not ignite.
Ignition System Fault / No Spark
Er02
Gas range shows Er02, and the gas burners shut off shortly after ignition.
Flame Supervision Device (FSD) / Thermocouple Fault
Er03
Gas cooktop shows Er03, and it continuously clicks even when the knobs are off.
Stuck Ignition Switch / Wet Ignition System
Er04
Gas range shows Er04, and one burner will not ignite while others work.
Individual Burner Ignition Failure
F01
Range oven display shows F01, and the oven will not heat.
Oven Temperature Sensor (Probe) Fault
F02
Range oven shows F02 and does not reach the set temperature.
Oven Overtemperature / Safety Thermostat Tripped
F03
Electronic SMEG oven shows F03 and will not start a cooking cycle.
Oven Door Lock / Door Switch Fault
F04
Oven display shows F04, and heating stops mid-cycle.
Oven Temperature Sensor Range/Drift Error
F05
SMEG oven shows F05, and the fan does not run in fan-forced mode.
Convection Fan Motor Fault
F06
Oven display shows F06, and the grill/broil element does not heat.
Grill/Broil Element Circuit Fault
F07
Oven shows F07, and the main lower element does not heat.
Lower Bake Element Circuit Fault
F08
Oven display shows F08, and the cooling fan runs continuously or not at all.
Cavity Cooling Fan Circuit Fault
F09
Oven shows F09, and clock/timer functions erratically.
Electronic Control Board / Clock Fault
F10
Oven shows F10, and it will not start the pyrolytic self-clean cycle.
Self-Clean System Fault
LOC
Oven display shows 'LOC' or a key symbol, and controls do not respond.
Child Lock / Control Lock Activated
Symptom
Burning smell, smoke, or electrical odor from range or cooktop.
Overheating Wiring or Component Failure
Symptom
Control knobs are hard to turn or feel loose on gas range.
Worn Gas Valve Spindles or Knob Sockets
Symptom
Cooktop glass or enamel surface is cracked.
Physical Damage to Cooking Surface
Symptom
Electric ceramic or induction cooktop zone does not heat at all.
Single Cooking Zone Failure
Symptom
Electric cooktop cycles on and off too frequently or does not reach high temperature.
Energy Regulator / Infinite Switch Fault
Symptom
Excessive condensation or steam escaping from oven door and control panel.
Oven Door Seal or Venting Issue
Symptom
Gas burner clicks and sparks, but will not light or takes a long time to light.
Restricted Gas Flow to Burner
Symptom
Gas burner flame is yellow, noisy, or lifts off the burner.
Incorrect Air-Gas Mixture / Burner Adjustment Fault
Symptom
Gas burner goes out when the knob is released (must hold the knob in to keep the flame).
Flame Failure Device Not Holding
Symptom
Gas burner will not ignite (no clicking, no spark), but gas is present.
Ignition System Power or Module Failure
Symptom
Oven does not heat at all (no elements work), but the display and lights are on.
Oven Power Distribution / Relay Board Failure
Symptom
Oven door does not close properly or drops open.
Door Hinge or Hinge Receiver Failure
Symptom
Oven fan is noisy, rattling, or scraping during operation.
Convection or Cooling Fan Mechanical Wear
Symptom
Oven interior light does not work.
Oven Lamp Circuit Failure
Symptom
Oven overheats and burns food, even at low temperature settings.
Oven Temperature Regulation Failure
Symptom
Oven takes a very long time to preheat or never reaches the set temperature.
Reduced Heating Capacity
Symptom
Strong gas smell around range or cooktop during or after use.
Gas Leak or Incomplete Combustion
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E0 |
The cooktop or range display shows E0, and burners will not operate.
|
Touch Control Panel Communication Fault | View Details |
| E1 |
The induction cooktop or electronic range shows E1 and disables one or more zones.
|
Cookware Detection / Induction Coil Fault | View Details |
| E2 |
An induction zone stops heating, and E2 appears on the display.
|
Induction Zone Overheating Protection | View Details |
| E3 |
The induction cooktop shows E3 and shuts down when high power is selected.
|
Supply Voltage Out of Range / Overvoltage | View Details |
| E4 |
Induction zone displays E4 and will not heat.
|
Induction Power Module Fault / IGBT Failure | View Details |
| E5 |
Induction cooktop shows E5 and beeps; zones shut down.
|
Cooktop Overtemperature / Glass Surface Overheat | View Details |
| E6 |
Induction cooktop displays E6 and will not start any zones.
|
Internal Communication Error Between User Interface and Power Module | View Details |
| E7 |
Induction zone shows E7 and does not heat properly.
|
Induction Coil Temperature Sensor Fault | View Details |
| E8 |
Induction cooktop intermittently shows E8, and zones cut out under load.
|
Internal Power Supply / Low Voltage on Control Electronics | View Details |
| E9 |
Induction cooktop shows E9, and all zones are disabled.
|
Configuration / Calibration Error | View Details |
| Er01 |
Gas cooktop with electronic ignition shows Er01, and the burners will not ignite.
|
Ignition System Fault / No Spark | View Details |
| Er02 |
Gas range shows Er02, and the gas burners shut off shortly after ignition.
|
Flame Supervision Device (FSD) / Thermocouple Fault | View Details |
| Er03 |
Gas cooktop shows Er03, and it continuously clicks even when the knobs are off.
|
Stuck Ignition Switch / Wet Ignition System | View Details |
| Er04 |
Gas range shows Er04, and one burner will not ignite while others work.
|
Individual Burner Ignition Failure | View Details |
| F01 |
Range oven display shows F01, and the oven will not heat.
|
Oven Temperature Sensor (Probe) Fault | View Details |
| F02 |
Range oven shows F02 and does not reach the set temperature.
|
Oven Overtemperature / Safety Thermostat Tripped | View Details |
| F03 |
Electronic SMEG oven shows F03 and will not start a cooking cycle.
|
Oven Door Lock / Door Switch Fault | View Details |
| F04 |
Oven display shows F04, and heating stops mid-cycle.
|
Oven Temperature Sensor Range/Drift Error | View Details |
| F05 |
SMEG oven shows F05, and the fan does not run in fan-forced mode.
|
Convection Fan Motor Fault | View Details |
| F06 |
Oven display shows F06, and the grill/broil element does not heat.
|
Grill/Broil Element Circuit Fault | View Details |
| F07 |
Oven shows F07, and the main lower element does not heat.
|
Lower Bake Element Circuit Fault | View Details |
| F08 |
Oven display shows F08, and the cooling fan runs continuously or not at all.
|
Cavity Cooling Fan Circuit Fault | View Details |
| F09 |
Oven shows F09, and clock/timer functions erratically.
|
Electronic Control Board / Clock Fault | View Details |
| F10 |
Oven shows F10, and it will not start the pyrolytic self-clean cycle.
|
Self-Clean System Fault | View Details |
| LOC |
Oven display shows 'LOC' or a key symbol, and controls do not respond.
|
Child Lock / Control Lock Activated | View Details |
| – |
Burning smell, smoke, or electrical odor from range or cooktop.
|
Overheating Wiring or Component Failure | View Details |
| – |
Control knobs are hard to turn or feel loose on gas range.
|
Worn Gas Valve Spindles or Knob Sockets | View Details |
| – |
Cooktop glass or enamel surface is cracked.
|
Physical Damage to Cooking Surface | View Details |
| – |
Electric ceramic or induction cooktop zone does not heat at all.
|
Single Cooking Zone Failure | View Details |
| – |
Electric cooktop cycles on and off too frequently or does not reach high temperature.
|
Energy Regulator / Infinite Switch Fault | View Details |
| – |
Excessive condensation or steam escaping from oven door and control panel.
|
Oven Door Seal or Venting Issue | View Details |
| – |
Gas burner clicks and sparks, but will not light or takes a long time to light.
|
Restricted Gas Flow to Burner | View Details |
| – |
Gas burner flame is yellow, noisy, or lifts off the burner.
|
Incorrect Air-Gas Mixture / Burner Adjustment Fault | View Details |
| – |
Gas burner goes out when the knob is released (must hold the knob in to keep the flame).
|
Flame Failure Device Not Holding | View Details |
| – |
Gas burner will not ignite (no clicking, no spark), but gas is present.
|
Ignition System Power or Module Failure | View Details |
| – |
Oven does not heat at all (no elements work), but the display and lights are on.
|
Oven Power Distribution / Relay Board Failure | View Details |
| – |
Oven door does not close properly or drops open.
|
Door Hinge or Hinge Receiver Failure | View Details |
| – |
Oven fan is noisy, rattling, or scraping during operation.
|
Convection or Cooling Fan Mechanical Wear | View Details |
| – |
Oven interior light does not work.
|
Oven Lamp Circuit Failure | View Details |
| – |
Oven overheats and burns food, even at low temperature settings.
|
Oven Temperature Regulation Failure | View Details |
| – |
Oven takes a very long time to preheat or never reaches the set temperature.
|
Reduced Heating Capacity | View Details |
| – |
Strong gas smell around range or cooktop during or after use.
|
Gas Leak or Incomplete Combustion | View Details |
No matching codes found
Advertisements