Logik Washer-Dryer Combos Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E01
Washer-dryer will not start; display shows E01 and door symbol may flash.
Door Lock Circuit Fault
E02
Washer-dryer does not fill with water or fills very slowly; E02 displayed.
Water Inlet Timeout / Fill Fault
E03
Washer-dryer will not drain; cycle stops with water in drum and E03 displayed.
Drain Pump Fault / Drain Timeout
E04
Washer-dryer overfills or shows E04 shortly after starting; may attempt to drain immediately.
Water Level Sensor / Overflow Fault
E05
Washer-dryer stops during wash or rinse; E05 displayed, often with cold water only.
NTC Temperature Sensor Fault
E06
Washer-dryer fails to heat water; cycle may run long and end with E06.
Heating Element / Heater Relay Fault
E07
Washer-dryer drum does not rotate during wash or spin; E07 displayed.
Drive Motor / Motor Control Fault
E08
Washer-dryer fails to reach or maintain spin speed; E08 displayed during spin phase.
Motor Speed Feedback / Tachometer Error
E09
Washer-dryer stops mid-cycle with E09; may be associated with motor not running at all.
Motor Power Supply / Triac Fault
E10
Washer-dryer does not start the drying cycle; E10 is displayed when switching to dry.
Dryer Heater / Drying System Fault
E11
Drying performance is poor or non-existent; E11 is displayed near the end of the drying cycle.
Dryer Temperature Sensor / NTC Fault
E12
The washer-dryer stops during drying; the drum may turn but there is no heat, and E12 is displayed.
Dryer Overheat / Thermal Cut-Out Fault
E13
Water is detected in the base tray; the washer-dryer may stop and show E13, sometimes with the pump running continuously.
Leak Detection / Anti-Flood Fault
E14
The washer-dryer fails to detect the water level correctly; it may not start or may stop with E14.
Pressure Switch Signal Error
E15
The washer-dryer shows E15 and will not start; this is often associated with the control panel not responding correctly.
User Interface / Control Panel Communication Fault
E16
The washer-dryer door will not unlock at the end of the cycle; E16 is displayed.
Door Unlock Fault
E17
The washer-dryer displays E17 and may stop during the spin cycle; this is often associated with excessive vibration.
Unbalanced Load / Spin Protection Fault
E18
The washer-dryer shows E18 and stops; this is often related to water not draining fully before the spin cycle.
Drainage / Pump Performance Fault
E19
The washer-dryer shows E19; this may be associated with detergent drawer issues or water not entering correctly.
Dispenser Valve / Drawer Sensor Fault
E20
General motor or drum rotation error; E20 displayed with intermittent or no drum movement.
General Motor Drive Error
Symptom
Control panel buttons are unresponsive or respond intermittently.
User Interface Keypad Fault
Symptom
Display is dim, flickering, or completely blank while the machine otherwise runs.
Display Module / Low-Voltage Supply Fault
Symptom
Door is difficult to close or pops open during a cycle without an error code.
Door Latch / Hinge Misalignment
Symptom
Drying cycle runs but clothes remain damp or take multiple cycles to dry.
Poor Drying Performance
Symptom
Washer-dryer combo will not power on at all; no lights or display.
No Mains Power / Power Supply Fault
Symptom
Washer-dryer emits a strong mouldy or musty odour from the drum.
Biofilm and Detergent Residue Build-Up
Symptom
Washer-dryer fills and drains but the drum does not turn during wash or spin (no error code).
Mechanical Drive Failure
Symptom
Washer-dryer is extremely noisy during spin; banging or rumbling sounds.
Drum Bearing or Suspension Failure
Symptom
Washer-dryer leaks water from the front door area during wash.
Door Seal (Gasket) Leak
Symptom
Washer-dryer leaks water from the rear or underneath during wash or drain.
Internal Hose or Tub Leak
Symptom
Washer-dryer leaves clothes soaking wet at the end of the cycle; no or very slow spin.
Spin Not Achieved / Drain or Balance Issue
Symptom
Washer-dryer leaves visible detergent or softener residues on clothes.
Poor Rinsing / Detergent Dispensing Issue
Symptom
Washer-dryer powers on but will not start any program; start button unresponsive.
Start Circuit / User Interface Fault
Symptom
Washer-dryer produces a burning smell during wash or dry cycles.
Overheating Component or Friction
Symptom
Washer-dryer stops during drying with water remaining in the drum.
Dryer Condensation / Pump-Out Fault
Symptom
Washer-dryer takes excessively long to complete cycles; it may seem to "stall" at certain times.
Extended Cycle Time / Heating or Sensor Issue
Symptom
Washer-dryer trips the household circuit breaker or RCD during operation.
Electrical Short or Earth Leakage
Symptom
Washer-dryer vibrates excessively or "walks" across the floor during spin.
Excessive Vibration / Installation Fault
Symptom
Water remains in the detergent or softener compartments after a cycle.
Dispenser Siphon / Jet Blockage
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E01 |
Washer-dryer will not start; display shows E01 and door symbol may flash.
|
Door Lock Circuit Fault | View Details |
| E02 |
Washer-dryer does not fill with water or fills very slowly; E02 displayed.
|
Water Inlet Timeout / Fill Fault | View Details |
| E03 |
Washer-dryer will not drain; cycle stops with water in drum and E03 displayed.
|
Drain Pump Fault / Drain Timeout | View Details |
| E04 |
Washer-dryer overfills or shows E04 shortly after starting; may attempt to drain immediately.
|
Water Level Sensor / Overflow Fault | View Details |
| E05 |
Washer-dryer stops during wash or rinse; E05 displayed, often with cold water only.
|
NTC Temperature Sensor Fault | View Details |
| E06 |
Washer-dryer fails to heat water; cycle may run long and end with E06.
|
Heating Element / Heater Relay Fault | View Details |
| E07 |
Washer-dryer drum does not rotate during wash or spin; E07 displayed.
|
Drive Motor / Motor Control Fault | View Details |
| E08 |
Washer-dryer fails to reach or maintain spin speed; E08 displayed during spin phase.
|
Motor Speed Feedback / Tachometer Error | View Details |
| E09 |
Washer-dryer stops mid-cycle with E09; may be associated with motor not running at all.
|
Motor Power Supply / Triac Fault | View Details |
| E10 |
Washer-dryer does not start the drying cycle; E10 is displayed when switching to dry.
|
Dryer Heater / Drying System Fault | View Details |
| E11 |
Drying performance is poor or non-existent; E11 is displayed near the end of the drying cycle.
|
Dryer Temperature Sensor / NTC Fault | View Details |
| E12 |
The washer-dryer stops during drying; the drum may turn but there is no heat, and E12 is displayed.
|
Dryer Overheat / Thermal Cut-Out Fault | View Details |
| E13 |
Water is detected in the base tray; the washer-dryer may stop and show E13, sometimes with the pump running continuously.
|
Leak Detection / Anti-Flood Fault | View Details |
| E14 |
The washer-dryer fails to detect the water level correctly; it may not start or may stop with E14.
|
Pressure Switch Signal Error | View Details |
| E15 |
The washer-dryer shows E15 and will not start; this is often associated with the control panel not responding correctly.
|
User Interface / Control Panel Communication Fault | View Details |
| E16 |
The washer-dryer door will not unlock at the end of the cycle; E16 is displayed.
|
Door Unlock Fault | View Details |
| E17 |
The washer-dryer displays E17 and may stop during the spin cycle; this is often associated with excessive vibration.
|
Unbalanced Load / Spin Protection Fault | View Details |
| E18 |
The washer-dryer shows E18 and stops; this is often related to water not draining fully before the spin cycle.
|
Drainage / Pump Performance Fault | View Details |
| E19 |
The washer-dryer shows E19; this may be associated with detergent drawer issues or water not entering correctly.
|
Dispenser Valve / Drawer Sensor Fault | View Details |
| E20 |
General motor or drum rotation error; E20 displayed with intermittent or no drum movement.
|
General Motor Drive Error | View Details |
| – |
Control panel buttons are unresponsive or respond intermittently.
|
User Interface Keypad Fault | View Details |
| – |
Display is dim, flickering, or completely blank while the machine otherwise runs.
|
Display Module / Low-Voltage Supply Fault | View Details |
| – |
Door is difficult to close or pops open during a cycle without an error code.
|
Door Latch / Hinge Misalignment | View Details |
| – |
Drying cycle runs but clothes remain damp or take multiple cycles to dry.
|
Poor Drying Performance | View Details |
| – |
Washer-dryer combo will not power on at all; no lights or display.
|
No Mains Power / Power Supply Fault | View Details |
| – |
Washer-dryer emits a strong mouldy or musty odour from the drum.
|
Biofilm and Detergent Residue Build-Up | View Details |
| – |
Washer-dryer fills and drains but the drum does not turn during wash or spin (no error code).
|
Mechanical Drive Failure | View Details |
| – |
Washer-dryer is extremely noisy during spin; banging or rumbling sounds.
|
Drum Bearing or Suspension Failure | View Details |
| – |
Washer-dryer leaks water from the front door area during wash.
|
Door Seal (Gasket) Leak | View Details |
| – |
Washer-dryer leaks water from the rear or underneath during wash or drain.
|
Internal Hose or Tub Leak | View Details |
| – |
Washer-dryer leaves clothes soaking wet at the end of the cycle; no or very slow spin.
|
Spin Not Achieved / Drain or Balance Issue | View Details |
| – |
Washer-dryer leaves visible detergent or softener residues on clothes.
|
Poor Rinsing / Detergent Dispensing Issue | View Details |
| – |
Washer-dryer powers on but will not start any program; start button unresponsive.
|
Start Circuit / User Interface Fault | View Details |
| – |
Washer-dryer produces a burning smell during wash or dry cycles.
|
Overheating Component or Friction | View Details |
| – |
Washer-dryer stops during drying with water remaining in the drum.
|
Dryer Condensation / Pump-Out Fault | View Details |
| – |
Washer-dryer takes excessively long to complete cycles; it may seem to "stall" at certain times.
|
Extended Cycle Time / Heating or Sensor Issue | View Details |
| – |
Washer-dryer trips the household circuit breaker or RCD during operation.
|
Electrical Short or Earth Leakage | View Details |
| – |
Washer-dryer vibrates excessively or "walks" across the floor during spin.
|
Excessive Vibration / Installation Fault | View Details |
| – |
Water remains in the detergent or softener compartments after a cycle.
|
Dispenser Siphon / Jet Blockage | View Details |
No matching codes found
Advertisements