Beko Washing Machines Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E01
Washer will not start; the door lock symbol flashes or the door will not lock at the beginning of the cycle.
Door Locking Failure
E02
Washer does not fill with water or fills very slowly; the cycle stops early with E02 on the display.
Water Inlet Timeout / Fill Fault
E03
Washer does not drain; water remains in the drum and E03 is displayed.
Drain Pump Timeout / Drainage Failure
E04
Washer overfills or shows E04; water may be seen in the door glass above the normal level, or the machine may attempt to drain immediately after filling.
Overfill / Pressure System Fault
E05
Washer stops during the cycle with E05; it may not heat the water or may take excessively long to complete.
Heating Circuit Fault
E06
Washer displays E06 and may not spin or may stop mid-cycle; sometimes associated with motor not running.
Motor Tachometer / Speed Sensor Fault
E07
Washer shows E07 and may not spin or may stop with drum locked; sometimes accompanied by unusual motor noise.
Motor Drive / Triac Fault
E08
Washer displays E08; drum may not turn or may turn erratically, especially on spin.
Motor Overload / Current Fault
E09
Washer shows E09 and will not start or stops shortly after starting; often related to power or PCB issues.
Control Board / Power Supply Fault
E10
Washer displays E10; often associated with water level or fill issues at the start of the cycle.
Water Level Detection Fault
E11
Washer shows E11; may not lock door or may unlock unexpectedly during cycle.
Door Lock Feedback Fault
E12
Washer displays E12; often related to communication or configuration issues between control modules (on models with separate display/control boards).
Communication Error Between Boards
E13
Washer shows E13; may be associated with water leakage into base or anti-flood system activation on some Beko models.
Leakage / Anti-Flood Fault
E16
Washer displays E16; often related to water inlet or valve configuration issues on some Beko models.
Secondary Water Inlet Fault
E17
Washer shows E17; may indicate a problem with the door being opened during operation or door lock timing.
Door Open During Cycle / Lock Timing Fault
E18
The washer displays E18; this is often associated with an unbalanced load or spin safety issues.
Unbalanced Load / Spin Safety Fault
E20
The washer shows E20; it may not drain or may stop before the spin cycle.
General Drainage / Pump Fault
E21
The washer displays E21; the drum does not rotate or rotates only briefly.
Motor Not Turning / Drive Fault
E23
The washer shows E23; this is often related to a drain pump triac or an electrical fault.
Drain Pump Control Fault
E30
The washer displays E30; this may be associated with door lock or safety circuit issues.
General Door Safety Fault
H1
The washer displays H1; this often indicates a heating sensor (NTC) fault on some Beko models.
NTC Temperature Sensor Fault
H2
The washer shows H2; this may indicate overheating or a heater relay fault.
Heater Overheat / Relay Stuck
H3
The washer displays H3; this is often related to motor overheating or a motor thermistor fault on some Beko models.
Motor Overheat / Thermistor Fault
H4
The washer shows H4; this may indicate a general heating system error on some Beko models.
General Heating System Error
H5
The washer displays H5; this is often associated with a water heating timeout (water not reaching the target temperature).
Heating Timeout Fault
Symptom
Washer displays random lights or segments on the display; buttons may not respond correctly; no specific error code.
Control Panel / UI Malfunction
Symptom
Washer does not take detergent or softener from the dispenser drawer properly; residues remain.
Dispenser / Water Flow Fault
Symptom
Washer door will not open at the end of the cycle; no error code.
Door Stuck Locked
Symptom
Washer drum does not spin at all, but machine fills and drains normally; no error code.
Drive Belt or Motor Drive Failure
Symptom
Washer emits a burning smell or visible sparks from underneath or the rear during operation.
Motor or Wiring Overheating
Symptom
Washer emits a sewage or rotten egg smell from the drain hose or standpipe during or after use.
Drain System Odor
Symptom
Washer has a strong musty or moldy smell inside the drum and on clothes.
Biofilm / Mold Build-Up
Symptom
Washer is leaking water from the front, especially during the wash or spin cycle; no error code is displayed.
Door Seal (Gasket) Leak
Symptom
Washer leaks from the rear or underneath during drain or spin; no error code.
Drain Hose or Sump Hose Leak
Symptom
Washer leaves clothes very wet at the end of the cycle; the spin cycle seems weak or short; no error code is displayed.
Poor Spin Performance / Unbalanced Load
Symptom
Washer makes loud banging or knocking noises during spin; drum may hit the cabinet.
Suspension / Shock Absorber Failure
Symptom
Washer powers on but will not start a cycle; Start/Pause button is unresponsive or just beeps.
User Interface / Control Lock Issue
Symptom
Washer produces a high-pitched whine or rumbling noise that intensifies at high spin speeds.
Drum Bearing Wear
Symptom
Washer stops mid-cycle and the door remains locked; water is still in the drum; no error code is displayed.
Intermittent Power or Control Fault
Symptom
Washer takes much longer than the displayed time to finish a cycle.
Cycle Time Extension / Auto-Adjust
Symptom
Washer vibrates excessively and "walks" across the floor during spin; no error code.
Excessive Vibration / Installation Issue
Symptom
Washer will not start; no lights or display, the unit is completely dead.
No Power / Main Supply Fault
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E01 |
Washer will not start; the door lock symbol flashes or the door will not lock at the beginning of the cycle.
|
Door Locking Failure | View Details |
| E02 |
Washer does not fill with water or fills very slowly; the cycle stops early with E02 on the display.
|
Water Inlet Timeout / Fill Fault | View Details |
| E03 |
Washer does not drain; water remains in the drum and E03 is displayed.
|
Drain Pump Timeout / Drainage Failure | View Details |
| E04 |
Washer overfills or shows E04; water may be seen in the door glass above the normal level, or the machine may attempt to drain immediately after filling.
|
Overfill / Pressure System Fault | View Details |
| E05 |
Washer stops during the cycle with E05; it may not heat the water or may take excessively long to complete.
|
Heating Circuit Fault | View Details |
| E06 |
Washer displays E06 and may not spin or may stop mid-cycle; sometimes associated with motor not running.
|
Motor Tachometer / Speed Sensor Fault | View Details |
| E07 |
Washer shows E07 and may not spin or may stop with drum locked; sometimes accompanied by unusual motor noise.
|
Motor Drive / Triac Fault | View Details |
| E08 |
Washer displays E08; drum may not turn or may turn erratically, especially on spin.
|
Motor Overload / Current Fault | View Details |
| E09 |
Washer shows E09 and will not start or stops shortly after starting; often related to power or PCB issues.
|
Control Board / Power Supply Fault | View Details |
| E10 |
Washer displays E10; often associated with water level or fill issues at the start of the cycle.
|
Water Level Detection Fault | View Details |
| E11 |
Washer shows E11; may not lock door or may unlock unexpectedly during cycle.
|
Door Lock Feedback Fault | View Details |
| E12 |
Washer displays E12; often related to communication or configuration issues between control modules (on models with separate display/control boards).
|
Communication Error Between Boards | View Details |
| E13 |
Washer shows E13; may be associated with water leakage into base or anti-flood system activation on some Beko models.
|
Leakage / Anti-Flood Fault | View Details |
| E16 |
Washer displays E16; often related to water inlet or valve configuration issues on some Beko models.
|
Secondary Water Inlet Fault | View Details |
| E17 |
Washer shows E17; may indicate a problem with the door being opened during operation or door lock timing.
|
Door Open During Cycle / Lock Timing Fault | View Details |
| E18 |
The washer displays E18; this is often associated with an unbalanced load or spin safety issues.
|
Unbalanced Load / Spin Safety Fault | View Details |
| E20 |
The washer shows E20; it may not drain or may stop before the spin cycle.
|
General Drainage / Pump Fault | View Details |
| E21 |
The washer displays E21; the drum does not rotate or rotates only briefly.
|
Motor Not Turning / Drive Fault | View Details |
| E23 |
The washer shows E23; this is often related to a drain pump triac or an electrical fault.
|
Drain Pump Control Fault | View Details |
| E30 |
The washer displays E30; this may be associated with door lock or safety circuit issues.
|
General Door Safety Fault | View Details |
| H1 |
The washer displays H1; this often indicates a heating sensor (NTC) fault on some Beko models.
|
NTC Temperature Sensor Fault | View Details |
| H2 |
The washer shows H2; this may indicate overheating or a heater relay fault.
|
Heater Overheat / Relay Stuck | View Details |
| H3 |
The washer displays H3; this is often related to motor overheating or a motor thermistor fault on some Beko models.
|
Motor Overheat / Thermistor Fault | View Details |
| H4 |
The washer shows H4; this may indicate a general heating system error on some Beko models.
|
General Heating System Error | View Details |
| H5 |
The washer displays H5; this is often associated with a water heating timeout (water not reaching the target temperature).
|
Heating Timeout Fault | View Details |
| – |
Washer displays random lights or segments on the display; buttons may not respond correctly; no specific error code.
|
Control Panel / UI Malfunction | View Details |
| – |
Washer does not take detergent or softener from the dispenser drawer properly; residues remain.
|
Dispenser / Water Flow Fault | View Details |
| – |
Washer door will not open at the end of the cycle; no error code.
|
Door Stuck Locked | View Details |
| – |
Washer drum does not spin at all, but machine fills and drains normally; no error code.
|
Drive Belt or Motor Drive Failure | View Details |
| – |
Washer emits a burning smell or visible sparks from underneath or the rear during operation.
|
Motor or Wiring Overheating | View Details |
| – |
Washer emits a sewage or rotten egg smell from the drain hose or standpipe during or after use.
|
Drain System Odor | View Details |
| – |
Washer has a strong musty or moldy smell inside the drum and on clothes.
|
Biofilm / Mold Build-Up | View Details |
| – |
Washer is leaking water from the front, especially during the wash or spin cycle; no error code is displayed.
|
Door Seal (Gasket) Leak | View Details |
| – |
Washer leaks from the rear or underneath during drain or spin; no error code.
|
Drain Hose or Sump Hose Leak | View Details |
| – |
Washer leaves clothes very wet at the end of the cycle; the spin cycle seems weak or short; no error code is displayed.
|
Poor Spin Performance / Unbalanced Load | View Details |
| – |
Washer makes loud banging or knocking noises during spin; drum may hit the cabinet.
|
Suspension / Shock Absorber Failure | View Details |
| – |
Washer powers on but will not start a cycle; Start/Pause button is unresponsive or just beeps.
|
User Interface / Control Lock Issue | View Details |
| – |
Washer produces a high-pitched whine or rumbling noise that intensifies at high spin speeds.
|
Drum Bearing Wear | View Details |
| – |
Washer stops mid-cycle and the door remains locked; water is still in the drum; no error code is displayed.
|
Intermittent Power or Control Fault | View Details |
| – |
Washer takes much longer than the displayed time to finish a cycle.
|
Cycle Time Extension / Auto-Adjust | View Details |
| – |
Washer vibrates excessively and "walks" across the floor during spin; no error code.
|
Excessive Vibration / Installation Issue | View Details |
| – |
Washer will not start; no lights or display, the unit is completely dead.
|
No Power / Main Supply Fault | View Details |
No matching codes found
Advertisements