CDA Washing Machines Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E01
Washer will not start a cycle and the door will not lock; E01 displayed on CDA washing machine.
Door Lock Circuit Failure
E02
Washer does not fill with water or fills very slowly; E02 displayed on CDA washing machine.
Water Inlet Timeout / Fill Fault
E03
Washer will not drain water; cycle stops with water in drum and E03 displayed on CDA washing machine.
Drain Pump Timeout / Drainage Fault
E04
Washer overfills, water level too high or water leaks from door; E04 displayed on CDA washing machine.
Overfill / Water Level Sensor Fault
E05
Washer does not heat water; cycles take unusually long or stop; E05 displayed on CDA washing machine.
Heating Circuit Failure
E06
Washer drum does not rotate or struggles to turn; E06 is displayed on the CDA washing machine.
Motor Drive Fault
E07
Washer drum does not spin at high speed; clothes come out very wet; E07 is displayed on the CDA washing machine.
Spin Cycle Fault / Unbalanced or Motor Speed Error
E08
Washer stops mid-cycle and displays E08; the drum may be locked or difficult to turn by hand.
Motor Overload / Drum Jam Fault
E09
Washer displays E09 and will not start or complete a cycle; it may trip the household circuit breaker.
Power Supply / Control Board Fault
E10
Washer fails to detect that the door is closed; E10 is displayed even though the door appears shut.
Door Status Detection Error
E11
Washer shows E11 and stops; water may remain in the drum, or the machine may not progress through the cycle.
Water Level Reading Error
E12
Washer displays E12 and may stop heating or abort the cycle.
Temperature Sensor (NTC) Fault
E13
Washer shows E13 and may stop with water in the base tray or not start at all.
Anti-Flood / Leak Detection Activated
E14
Washer displays E14 and may not respond to control inputs; the buttons or dial appear unresponsive.
User Interface / Control Panel Communication Fault
E15
Washer shows E15 and may not lock the door or start; this sometimes appears after a power surge.
Configuration / EEPROM Error
E16
Washer displays E16 and may stop during spin or high-speed operation.
Excessive Vibration / Out-of-Balance Error
E17
Washer shows E17 and may not fill correctly; sometimes associated with hot/cold fill issues on dual-valve models.
Inlet Valve Configuration / Flow Error
E18
Washer displays E18 and stops; often related to drain issues but may differ from E03 timing.
Partial Drain / Pump Performance Error
E19
Washer shows E19 and may not advance through programs; selector dial position may not be recognized.
Program Selector / Encoder Fault
E20
Washer displays E20 and may stop with water in drum or fail to start spin.
General Drain / Pump or Pressure Interaction Fault
Symptom
The washer displays an incorrect time remaining or frequently pauses and extends the cycle duration.
Adaptive Cycle Extension / Heating or Load Issues
Symptom
The washer door will not open at the end of the cycle; no error code is displayed.
Door Lock Stuck Closed
Symptom
The washer emits a burning smell during operation.
Overheating Component or Belt Slippage
Symptom
The washer has a persistent musty or moldy smell inside the drum.
Biofilm and Detergent Residue Build-Up
Symptom
The washer intermittently trips the household RCD (residual current device) during operation.
Earth Leakage / Insulation Fault
Symptom
The washer leaks water from the front door area during the wash cycle.
Door Seal (Gasket) Leak
Symptom
The washer leaks water from underneath the machine.
Internal Hose or Pump Leak
Symptom
The washer leaves clothes soaking wet at the end of the cycle, but no error code is shown.
Poor Spin Performance
Symptom
The washer leaves detergent or softener in the dispenser drawer at the end of the cycle.
Poor Dispenser Flushing
Symptom
The washer vibrates excessively and 'walks' across the floor during the spin cycle, even when level.
Severe Out-of-Balance Movement
Symptom
Washer displays random lights or resets mid-cycle without showing a specific error code.
Intermittent Power or Control Fault
Symptom
Washer drum does not fill fully; water level appears very low but machine operates.
Perceived Low Water Level (Normal Operation) or Underfill
Symptom
Washer fills and drains but drum does not turn at all during wash or spin.
Drum Drive Failure
Symptom
Washer is dead: no lights, no display, no response when power button is pressed.
No Power / Dead Appliance
Symptom
Washer makes loud banging or knocking noises during spin.
Excessive Vibration / Suspension Wear
Symptom
Washer powers on but will not start any program; Start button beeps or flashes but cycle does not begin.
Start Inhibit / Safety Interlock Not Satisfied
Symptom
Washer produces a high-pitched squeal or grinding noise when spinning.
Drum Bearing or Drive Pulley Wear
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E01 |
Washer will not start a cycle and the door will not lock; E01 displayed on CDA washing machine.
|
Door Lock Circuit Failure | View Details |
| E02 |
Washer does not fill with water or fills very slowly; E02 displayed on CDA washing machine.
|
Water Inlet Timeout / Fill Fault | View Details |
| E03 |
Washer will not drain water; cycle stops with water in drum and E03 displayed on CDA washing machine.
|
Drain Pump Timeout / Drainage Fault | View Details |
| E04 |
Washer overfills, water level too high or water leaks from door; E04 displayed on CDA washing machine.
|
Overfill / Water Level Sensor Fault | View Details |
| E05 |
Washer does not heat water; cycles take unusually long or stop; E05 displayed on CDA washing machine.
|
Heating Circuit Failure | View Details |
| E06 |
Washer drum does not rotate or struggles to turn; E06 is displayed on the CDA washing machine.
|
Motor Drive Fault | View Details |
| E07 |
Washer drum does not spin at high speed; clothes come out very wet; E07 is displayed on the CDA washing machine.
|
Spin Cycle Fault / Unbalanced or Motor Speed Error | View Details |
| E08 |
Washer stops mid-cycle and displays E08; the drum may be locked or difficult to turn by hand.
|
Motor Overload / Drum Jam Fault | View Details |
| E09 |
Washer displays E09 and will not start or complete a cycle; it may trip the household circuit breaker.
|
Power Supply / Control Board Fault | View Details |
| E10 |
Washer fails to detect that the door is closed; E10 is displayed even though the door appears shut.
|
Door Status Detection Error | View Details |
| E11 |
Washer shows E11 and stops; water may remain in the drum, or the machine may not progress through the cycle.
|
Water Level Reading Error | View Details |
| E12 |
Washer displays E12 and may stop heating or abort the cycle.
|
Temperature Sensor (NTC) Fault | View Details |
| E13 |
Washer shows E13 and may stop with water in the base tray or not start at all.
|
Anti-Flood / Leak Detection Activated | View Details |
| E14 |
Washer displays E14 and may not respond to control inputs; the buttons or dial appear unresponsive.
|
User Interface / Control Panel Communication Fault | View Details |
| E15 |
Washer shows E15 and may not lock the door or start; this sometimes appears after a power surge.
|
Configuration / EEPROM Error | View Details |
| E16 |
Washer displays E16 and may stop during spin or high-speed operation.
|
Excessive Vibration / Out-of-Balance Error | View Details |
| E17 |
Washer shows E17 and may not fill correctly; sometimes associated with hot/cold fill issues on dual-valve models.
|
Inlet Valve Configuration / Flow Error | View Details |
| E18 |
Washer displays E18 and stops; often related to drain issues but may differ from E03 timing.
|
Partial Drain / Pump Performance Error | View Details |
| E19 |
Washer shows E19 and may not advance through programs; selector dial position may not be recognized.
|
Program Selector / Encoder Fault | View Details |
| E20 |
Washer displays E20 and may stop with water in drum or fail to start spin.
|
General Drain / Pump or Pressure Interaction Fault | View Details |
| – |
The washer displays an incorrect time remaining or frequently pauses and extends the cycle duration.
|
Adaptive Cycle Extension / Heating or Load Issues | View Details |
| – |
The washer door will not open at the end of the cycle; no error code is displayed.
|
Door Lock Stuck Closed | View Details |
| – |
The washer emits a burning smell during operation.
|
Overheating Component or Belt Slippage | View Details |
| – |
The washer has a persistent musty or moldy smell inside the drum.
|
Biofilm and Detergent Residue Build-Up | View Details |
| – |
The washer intermittently trips the household RCD (residual current device) during operation.
|
Earth Leakage / Insulation Fault | View Details |
| – |
The washer leaks water from the front door area during the wash cycle.
|
Door Seal (Gasket) Leak | View Details |
| – |
The washer leaks water from underneath the machine.
|
Internal Hose or Pump Leak | View Details |
| – |
The washer leaves clothes soaking wet at the end of the cycle, but no error code is shown.
|
Poor Spin Performance | View Details |
| – |
The washer leaves detergent or softener in the dispenser drawer at the end of the cycle.
|
Poor Dispenser Flushing | View Details |
| – |
The washer vibrates excessively and 'walks' across the floor during the spin cycle, even when level.
|
Severe Out-of-Balance Movement | View Details |
| – |
Washer displays random lights or resets mid-cycle without showing a specific error code.
|
Intermittent Power or Control Fault | View Details |
| – |
Washer drum does not fill fully; water level appears very low but machine operates.
|
Perceived Low Water Level (Normal Operation) or Underfill | View Details |
| – |
Washer fills and drains but drum does not turn at all during wash or spin.
|
Drum Drive Failure | View Details |
| – |
Washer is dead: no lights, no display, no response when power button is pressed.
|
No Power / Dead Appliance | View Details |
| – |
Washer makes loud banging or knocking noises during spin.
|
Excessive Vibration / Suspension Wear | View Details |
| – |
Washer powers on but will not start any program; Start button beeps or flashes but cycle does not begin.
|
Start Inhibit / Safety Interlock Not Satisfied | View Details |
| – |
Washer produces a high-pitched squeal or grinding noise when spinning.
|
Drum Bearing or Drive Pulley Wear | View Details |
No matching codes found
Advertisements