Comfee
Comfee Washing Machines Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E1
Washer stops mid-cycle and displays E1; often occurs during wash or rinse fill stage.
Water Inlet Timeout / Water Fill Error
E10
The washer displays E10 and does not start the cycle; this is often related to the door not locking or the control board not recognizing that the door is closed.
Door Not Closed / Door Switch Recognition Error
E2
Washer displays E2 and will not advance; often associated with lid/door not locking or unlocking properly.
Door/Lid Lock Error
E21
The washer displays E21 and stops with water remaining in the tub; the drain pump may hum but fail to evacuate the water.
Severe Drain Blockage / Pump Overload
E3
Washer shows E3 and drum does not spin or only jerks slightly; may occur at start of wash or spin.
Motor Drive Fault / Motor Unable to Start
E30
The washer displays E30 and may not start or may stop unexpectedly; this is often associated with internal communication issues.
Control Board Communication Error
E31
The washer displays E31 and may fail to heat or may misread the water temperature.
NTC Temperature Sensor Error
E4
Washer displays E4 and may stop during spin; drum may be banging or heavily vibrating before the error appears.
Unbalanced Load / Out-of-Balance Protection
E40
The washer displays E40 and will not start; the door symbol may flash on the display.
Door Locking Failure
E41
The washer displays E41 even though the door appears to be closed; the cycle will not start.
Door Open Signal Error
E5
Washer shows E5 and will not drain or takes a very long time to drain; water remains in drum.
Drain Pump Error / Drain Timeout
E50
The washer displays E50 and may fail to spin or agitate; the motor may remain silent.
General Motor Error
E51
The washer displays E51 and may start to spin and then stop; this is sometimes accompanied by a burning smell.
Motor Triac / Motor Control Short
E6
Washer displays E6 and may stop heating water or halt mid-cycle; sometimes associated with lukewarm washes.
Water Heating Error / Heater Circuit Fault
E60
The washer displays E60 and does not heat the water properly; cycles may take longer than normal.
Heating System General Error
E7
Washer shows E7 and may not detect correct water level; can overfill, underfill, or stop unexpectedly.
Water Level Sensor / Pressure Switch Error
E8
Washer displays E8 and may not spin at high speed; drum may start then stop repeatedly.
Motor Overload / Tachometer Feedback Error
E9
The washer displays E9 and may leak or stop with a water level error; this sometimes occurs after moving the machine.
Overflow / Water Leak Detection Error
E90
Washer shows E90 and becomes unresponsive or stuck; may occur after a power outage.
Configuration / Software Communication Error
Symptom
The washer displays an incorrect water temperature or washes with very hot water on a cold setting.
Temperature Control / Valve Misconnection
Symptom
The washer door will not unlock at the end of the cycle; clothes are trapped inside.
Door Lock Stuck / Fail-to-Unlock
Symptom
The washer drum does not turn freely by hand; it feels jammed or scrapes.
Drum Obstruction / Mechanical Jam
Symptom
The washer drum hits the cabinet or makes scraping noises during the spin cycle.
Drum Support / Spider Arm Damage
Symptom
The washer emits a burning rubber smell during the spin or wash cycle.
Belt Slippage / Overheating Component
Symptom
The washer emits a strong electrical or plastic burning smell and may shut down.
Electrical Overheating / Component Failure
Symptom
The washer intermittently stops mid-cycle without any error code; it may resume after some time.
Intermittent Power / Overheating Protection
Symptom
The washer leaves clothes covered in detergent residue or white streaks after the wash cycle.
Poor Rinsing / Detergent Residue
Symptom
The washer takes much longer than normal to complete a cycle.
Extended Cycle Time / Control Compensation
Symptom
The washer's control panel buttons are unresponsive, or some buttons do not work.
User Interface Keypad Failure
Symptom
The washer's detergent drawer overflows or leaks water down the front.
Detergent Dispenser Overflow
Symptom
The washer's drum light (if equipped) does not turn on, but the machine otherwise works.
Drum Light Failure
Symptom
Washer fills with water but does not agitate or tumble; drum stays still during wash phase.
No Agitation / No Tumble
Symptom
Washer has a strong moldy or musty odor, especially from the drum or door gasket.
Biofilm / Mold Build-up
Symptom
Washer is very noisy during spin; loud rumbling or grinding sound from the rear.
Drum Bearing Failure
Symptom
Washer leaks water from the front door area during wash or spin.
Door Gasket / Seal Leak
Symptom
Washer leaks water from underneath the cabinet.
Internal Hose or Tub Leak
Symptom
Washer makes a loud banging or knocking noise during spin; machine may move or walk across the floor.
Excessive Vibration / Suspension Failure
Symptom
Washer powers on but will not start any cycle; pressing Start does nothing.
Start Circuit / User Interface Failure
Symptom
Washer will not power on at all; no lights or display, completely dead.
No Power / Dead Appliance
Symptom
Washer will not spin or spins very slowly; clothes come out very wet.
No Spin / Poor Spin Performance
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E1 |
Washer stops mid-cycle and displays E1; often occurs during wash or rinse fill stage.
|
Water Inlet Timeout / Water Fill Error | View Details |
| E10 |
The washer displays E10 and does not start the cycle; this is often related to the door not locking or the control board not recognizing that the door is closed.
|
Door Not Closed / Door Switch Recognition Error | View Details |
| E2 |
Washer displays E2 and will not advance; often associated with lid/door not locking or unlocking properly.
|
Door/Lid Lock Error | View Details |
| E21 |
The washer displays E21 and stops with water remaining in the tub; the drain pump may hum but fail to evacuate the water.
|
Severe Drain Blockage / Pump Overload | View Details |
| E3 |
Washer shows E3 and drum does not spin or only jerks slightly; may occur at start of wash or spin.
|
Motor Drive Fault / Motor Unable to Start | View Details |
| E30 |
The washer displays E30 and may not start or may stop unexpectedly; this is often associated with internal communication issues.
|
Control Board Communication Error | View Details |
| E31 |
The washer displays E31 and may fail to heat or may misread the water temperature.
|
NTC Temperature Sensor Error | View Details |
| E4 |
Washer displays E4 and may stop during spin; drum may be banging or heavily vibrating before the error appears.
|
Unbalanced Load / Out-of-Balance Protection | View Details |
| E40 |
The washer displays E40 and will not start; the door symbol may flash on the display.
|
Door Locking Failure | View Details |
| E41 |
The washer displays E41 even though the door appears to be closed; the cycle will not start.
|
Door Open Signal Error | View Details |
| E5 |
Washer shows E5 and will not drain or takes a very long time to drain; water remains in drum.
|
Drain Pump Error / Drain Timeout | View Details |
| E50 |
The washer displays E50 and may fail to spin or agitate; the motor may remain silent.
|
General Motor Error | View Details |
| E51 |
The washer displays E51 and may start to spin and then stop; this is sometimes accompanied by a burning smell.
|
Motor Triac / Motor Control Short | View Details |
| E6 |
Washer displays E6 and may stop heating water or halt mid-cycle; sometimes associated with lukewarm washes.
|
Water Heating Error / Heater Circuit Fault | View Details |
| E60 |
The washer displays E60 and does not heat the water properly; cycles may take longer than normal.
|
Heating System General Error | View Details |
| E7 |
Washer shows E7 and may not detect correct water level; can overfill, underfill, or stop unexpectedly.
|
Water Level Sensor / Pressure Switch Error | View Details |
| E8 |
Washer displays E8 and may not spin at high speed; drum may start then stop repeatedly.
|
Motor Overload / Tachometer Feedback Error | View Details |
| E9 |
The washer displays E9 and may leak or stop with a water level error; this sometimes occurs after moving the machine.
|
Overflow / Water Leak Detection Error | View Details |
| E90 |
Washer shows E90 and becomes unresponsive or stuck; may occur after a power outage.
|
Configuration / Software Communication Error | View Details |
| – |
The washer displays an incorrect water temperature or washes with very hot water on a cold setting.
|
Temperature Control / Valve Misconnection | View Details |
| – |
The washer door will not unlock at the end of the cycle; clothes are trapped inside.
|
Door Lock Stuck / Fail-to-Unlock | View Details |
| – |
The washer drum does not turn freely by hand; it feels jammed or scrapes.
|
Drum Obstruction / Mechanical Jam | View Details |
| – |
The washer drum hits the cabinet or makes scraping noises during the spin cycle.
|
Drum Support / Spider Arm Damage | View Details |
| – |
The washer emits a burning rubber smell during the spin or wash cycle.
|
Belt Slippage / Overheating Component | View Details |
| – |
The washer emits a strong electrical or plastic burning smell and may shut down.
|
Electrical Overheating / Component Failure | View Details |
| – |
The washer intermittently stops mid-cycle without any error code; it may resume after some time.
|
Intermittent Power / Overheating Protection | View Details |
| – |
The washer leaves clothes covered in detergent residue or white streaks after the wash cycle.
|
Poor Rinsing / Detergent Residue | View Details |
| – |
The washer takes much longer than normal to complete a cycle.
|
Extended Cycle Time / Control Compensation | View Details |
| – |
The washer's control panel buttons are unresponsive, or some buttons do not work.
|
User Interface Keypad Failure | View Details |
| – |
The washer's detergent drawer overflows or leaks water down the front.
|
Detergent Dispenser Overflow | View Details |
| – |
The washer's drum light (if equipped) does not turn on, but the machine otherwise works.
|
Drum Light Failure | View Details |
| – |
Washer fills with water but does not agitate or tumble; drum stays still during wash phase.
|
No Agitation / No Tumble | View Details |
| – |
Washer has a strong moldy or musty odor, especially from the drum or door gasket.
|
Biofilm / Mold Build-up | View Details |
| – |
Washer is very noisy during spin; loud rumbling or grinding sound from the rear.
|
Drum Bearing Failure | View Details |
| – |
Washer leaks water from the front door area during wash or spin.
|
Door Gasket / Seal Leak | View Details |
| – |
Washer leaks water from underneath the cabinet.
|
Internal Hose or Tub Leak | View Details |
| – |
Washer makes a loud banging or knocking noise during spin; machine may move or walk across the floor.
|
Excessive Vibration / Suspension Failure | View Details |
| – |
Washer powers on but will not start any cycle; pressing Start does nothing.
|
Start Circuit / User Interface Failure | View Details |
| – |
Washer will not power on at all; no lights or display, completely dead.
|
No Power / Dead Appliance | View Details |
| – |
Washer will not spin or spins very slowly; clothes come out very wet.
|
No Spin / Poor Spin Performance | View Details |
No matching codes found
Advertisements