Dawlance Washing Machines Error Codes
Complete list of fault codes and troubleshooting guides. Use the search below to find your specific error.
Advertisements
E1
The washer does not take in water, the cycle will not start, and E1 is displayed on the Dawlance washer display.
Water Inlet Timeout / No Fill
E10
Washer shows E10 and does not start; the display may be blank or flicker when power is applied.
Power Supply / Voltage Error
E11
Washer displays E11 and stops; the door remains locked, and the cycle cannot continue.
Door Lock Communication Error
E12
Washer shows E12 and does not heat water; cycles may take longer than normal.
Heater Circuit Error
E13
Washer displays E13 and stops; water may be found in the base tray or under the machine.
Leakage / Overflow Protection (Base Sensor)
E2
The washer does not drain water, the drum remains full, and E2 is displayed on the Dawlance washing machine.
Drain Timeout / Drain Failure
E21
Dawlance front-load washer shows E21 and will not drain or spin.
Extended Drain Time / Pump Blockage
E22
Washer shows E22; water remains in the drum, and the door stays locked at the end of the cycle.
Drain Pump Electrical Fault
E3
The washer drum does not spin or the spin is very weak, and E3 is displayed on the Dawlance washer.
Motor Drive Fault / Spin Failure
E30
Dawlance washer shows E30 and stops; the drum may not rotate at all.
Motor Tachometer / Speed Sensor Error
E31
Washer displays E31; the drum may start then stop repeatedly without reaching full speed.
Motor Drive Overcurrent / Stall Detection
E4
The washer displays E4 and stops during the spin cycle; the drum shakes violently or refuses to spin up.
Unbalanced Load / Out-of-Balance Protection
E40
Washer displays E40 and will not start; the door symbol may flash.
Door Not Properly Closed
E41
Washer displays E41; the door appears closed but the machine thinks it is open.
Door Lock Signal Error
E5
The washer stops mid-cycle with E5; the water level does not reach the correct height or overfills slightly before stopping.
Water Level Sensor / Pressure Switch Error
E50
Dawlance washer displays E50; the motor does not run or runs erratically.
General Motor Error
E6
The washer shows E6 and will not start or stops suddenly; this is sometimes accompanied by humming or no motor movement.
Motor Protection / Motor Overload Error
E60
Washer displays E60; water does not heat or heats too slowly.
Heating System General Error
E7
The washer displays E7 and does not start spinning; the lid or door status seems incorrect.
Lid Switch / Door Lock Error
E8
Washer shows E8 and stops; water temperature seems incorrect, or the cycle ends quickly.
Temperature Sensor (NTC) Error
E9
Washer displays E9 and may stop filling or draining; water level readings appear erratic.
Water Overflow / Overfill Protection
E90
Washer displays E90; the machine may not start or respond to button presses.
Communication Error Between Display and Main PCB
Symptom
Semi-automatic Dawlance washer's spin tub vibrates excessively and hits the cabinet.
Spin Tub Imbalance / Suspension Fault (Twin-Tub)
Symptom
The top-load Dawlance washer agitator or pulsator does not move during the wash cycle, but the spin cycle works.
Agitator / Pulsator Drive Failure
Symptom
The top-load Dawlance washer spins but does not drain water from the outer tub (twin-tub / semi-automatic).
Drain Selector / Drain Valve Failure
Symptom
The washer door or lid is stuck locked after a cycle ends; no error code is displayed.
Door Lock Stuck Closed
Symptom
The washer drum does not turn freely by hand; there is a scraping or metallic rubbing noise when rotated.
Foreign Object Between Drum and Tub
Symptom
The washer emits a burning smell during operation; this may be accompanied by smoke or excessive heat.
Electrical Overheating / Component Burn
Symptom
The washer leaves detergent residue or white streaks on clothes after washing.
Poor Rinsing / Detergent Residue
Symptom
The washer makes a loud banging or knocking noise during the spin cycle; the machine may move across the floor.
Excessive Vibration / Suspension Failure
Symptom
The washer produces a strong moldy or musty odor from the drum or door gasket.
Microbial Growth / Odor Build-Up
Symptom
The washer takes too long to complete a cycle; the time remaining on the display increases or stays high.
Extended Cycle Time
Symptom
Washer display and lights flicker or reset during operation.
Intermittent Power / Voltage Drop
Symptom
Washer does not spin at the end of the cycle; clothes come out very wet.
No Final Spin
Symptom
Washer does not take fabric softener or detergent from the drawer; compartments remain full after cycle.
Dispenser Drawer Flow Problem
Symptom
Washer drum rotates only in one direction during wash or does not reverse as usual.
Reversing Motor Control Fault
Symptom
Washer fills with water but does not start washing; the drum does not move.
Wash Motor Not Running
Symptom
Washer is dead; no lights or response when the power button is pressed.
No Power / Dead Appliance
Symptom
Washer is very noisy during spin; a loud rumbling or grinding sound from the drum area.
Drum Bearing Failure
Symptom
Washer overfills and water level is higher than normal without showing an error code.
Water Level Control Failure
Symptom
Water is leaking from under the Dawlance washer during or after a cycle.
General Water Leak
| Error Code | Symptom | Fault Type | Guide |
|---|---|---|---|
| E1 |
The washer does not take in water, the cycle will not start, and E1 is displayed on the Dawlance washer display.
|
Water Inlet Timeout / No Fill | View Details |
| E10 |
Washer shows E10 and does not start; the display may be blank or flicker when power is applied.
|
Power Supply / Voltage Error | View Details |
| E11 |
Washer displays E11 and stops; the door remains locked, and the cycle cannot continue.
|
Door Lock Communication Error | View Details |
| E12 |
Washer shows E12 and does not heat water; cycles may take longer than normal.
|
Heater Circuit Error | View Details |
| E13 |
Washer displays E13 and stops; water may be found in the base tray or under the machine.
|
Leakage / Overflow Protection (Base Sensor) | View Details |
| E2 |
The washer does not drain water, the drum remains full, and E2 is displayed on the Dawlance washing machine.
|
Drain Timeout / Drain Failure | View Details |
| E21 |
Dawlance front-load washer shows E21 and will not drain or spin.
|
Extended Drain Time / Pump Blockage | View Details |
| E22 |
Washer shows E22; water remains in the drum, and the door stays locked at the end of the cycle.
|
Drain Pump Electrical Fault | View Details |
| E3 |
The washer drum does not spin or the spin is very weak, and E3 is displayed on the Dawlance washer.
|
Motor Drive Fault / Spin Failure | View Details |
| E30 |
Dawlance washer shows E30 and stops; the drum may not rotate at all.
|
Motor Tachometer / Speed Sensor Error | View Details |
| E31 |
Washer displays E31; the drum may start then stop repeatedly without reaching full speed.
|
Motor Drive Overcurrent / Stall Detection | View Details |
| E4 |
The washer displays E4 and stops during the spin cycle; the drum shakes violently or refuses to spin up.
|
Unbalanced Load / Out-of-Balance Protection | View Details |
| E40 |
Washer displays E40 and will not start; the door symbol may flash.
|
Door Not Properly Closed | View Details |
| E41 |
Washer displays E41; the door appears closed but the machine thinks it is open.
|
Door Lock Signal Error | View Details |
| E5 |
The washer stops mid-cycle with E5; the water level does not reach the correct height or overfills slightly before stopping.
|
Water Level Sensor / Pressure Switch Error | View Details |
| E50 |
Dawlance washer displays E50; the motor does not run or runs erratically.
|
General Motor Error | View Details |
| E6 |
The washer shows E6 and will not start or stops suddenly; this is sometimes accompanied by humming or no motor movement.
|
Motor Protection / Motor Overload Error | View Details |
| E60 |
Washer displays E60; water does not heat or heats too slowly.
|
Heating System General Error | View Details |
| E7 |
The washer displays E7 and does not start spinning; the lid or door status seems incorrect.
|
Lid Switch / Door Lock Error | View Details |
| E8 |
Washer shows E8 and stops; water temperature seems incorrect, or the cycle ends quickly.
|
Temperature Sensor (NTC) Error | View Details |
| E9 |
Washer displays E9 and may stop filling or draining; water level readings appear erratic.
|
Water Overflow / Overfill Protection | View Details |
| E90 |
Washer displays E90; the machine may not start or respond to button presses.
|
Communication Error Between Display and Main PCB | View Details |
| – |
Semi-automatic Dawlance washer's spin tub vibrates excessively and hits the cabinet.
|
Spin Tub Imbalance / Suspension Fault (Twin-Tub) | View Details |
| – |
The top-load Dawlance washer agitator or pulsator does not move during the wash cycle, but the spin cycle works.
|
Agitator / Pulsator Drive Failure | View Details |
| – |
The top-load Dawlance washer spins but does not drain water from the outer tub (twin-tub / semi-automatic).
|
Drain Selector / Drain Valve Failure | View Details |
| – |
The washer door or lid is stuck locked after a cycle ends; no error code is displayed.
|
Door Lock Stuck Closed | View Details |
| – |
The washer drum does not turn freely by hand; there is a scraping or metallic rubbing noise when rotated.
|
Foreign Object Between Drum and Tub | View Details |
| – |
The washer emits a burning smell during operation; this may be accompanied by smoke or excessive heat.
|
Electrical Overheating / Component Burn | View Details |
| – |
The washer leaves detergent residue or white streaks on clothes after washing.
|
Poor Rinsing / Detergent Residue | View Details |
| – |
The washer makes a loud banging or knocking noise during the spin cycle; the machine may move across the floor.
|
Excessive Vibration / Suspension Failure | View Details |
| – |
The washer produces a strong moldy or musty odor from the drum or door gasket.
|
Microbial Growth / Odor Build-Up | View Details |
| – |
The washer takes too long to complete a cycle; the time remaining on the display increases or stays high.
|
Extended Cycle Time | View Details |
| – |
Washer display and lights flicker or reset during operation.
|
Intermittent Power / Voltage Drop | View Details |
| – |
Washer does not spin at the end of the cycle; clothes come out very wet.
|
No Final Spin | View Details |
| – |
Washer does not take fabric softener or detergent from the drawer; compartments remain full after cycle.
|
Dispenser Drawer Flow Problem | View Details |
| – |
Washer drum rotates only in one direction during wash or does not reverse as usual.
|
Reversing Motor Control Fault | View Details |
| – |
Washer fills with water but does not start washing; the drum does not move.
|
Wash Motor Not Running | View Details |
| – |
Washer is dead; no lights or response when the power button is pressed.
|
No Power / Dead Appliance | View Details |
| – |
Washer is very noisy during spin; a loud rumbling or grinding sound from the drum area.
|
Drum Bearing Failure | View Details |
| – |
Washer overfills and water level is higher than normal without showing an error code.
|
Water Level Control Failure | View Details |
| – |
Water is leaking from under the Dawlance washer during or after a cycle.
|
General Water Leak | View Details |
No matching codes found
Advertisements